2014 F-Series Super Duty Class A Motorhome and Commercial Owner’s Manual

and Commercial Chassis Owner’s Manual

image2image3image4image5image6image7

fordowner.com  ford.ca

image8image9image10image11

EU9J 19A321 AC | June 2014 | Third Printing | Owner’s Manual | Motorhome | Litho in U.S.A.

image12image13The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted.

© Ford Motor Company 2014

All rights reserved.

Part Number: 20140521215744

image14image15

image16image17

Table of Contents

image18

Introduction

About This Manual  3

Symbols Glossary  3

California Proposition 65  5

Perchlorate  5

Ford Credit  5

Replacement Parts

Recommendation  6

Special Notices  6

Mobile Communications

Equipment  7

Export Unique Options  7

Steering Wheel

Adjusting the Steering Wheel  8

Cruise Control  8

Wipers and Washers

Windshield Wipers  9

Windshield Washers  9

Lighting

Lighting Control  10

Instrument Lighting Dimmer  10

Daytime Running Lamps  11

Direction Indicators  11

Instrument Cluster

Gauges  12

Warning Lamps and Indicators  13

Audible Warnings and Indicators  15

Information Displays

General Information  16

Information Messages  17

Starting and Stopping the

Engine

General Information  20

Ignition Switch  20

image19

1

Starting a Gasoline Engine  20

Fuel and Refueling

Safety Precautions  22

Fuel Quality  23

Running Out of Fuel  23

Refueling  24

Fuel Consumption  25

Emission Control System  26

Transmission

Automatic Transmission  29

Brakes

General Information  33

Hints on Driving With Anti-Lock

Brakes  33

Parking Brake  34

Cruise Control

Principle of Operation  35

Using Cruise Control  35

Load Carrying

Load Limit  36

Towing

Towing a Trailer  42

Recommended Towing Weights  43

Essential Towing Checks  44

Transporting the Vehicle  46

Towing the Vehicle on Four Wheels  47

Driving Hints

Breaking-In  48

Economical Driving  48

Driving Through Water  49

Roadside Emergencies

Roadside Assistance  50

image20

Motorhome (TY3) , enUSA

image21image22

Table of Contents

image23

Hazard Warning Flashers………………………..

51

Cleaning the Alloy Wheels…………………….

88

Jump Starting the Vehicle……………………….

51

Vehicle Storage……………………………………….

88

Customer Assistance

Getting the Services You Need  54

In California (U.S. Only)  55

The Better Business Bureau (BBB) Auto

Line Program (U.S. Only)  56

Utilizing the Mediation/Arbitration

Program (Canada Only)  56

Getting Assistance Outside the U.S. and

Canada  57

Ordering Additional Owner’s

Literature  58

Reporting Safety Defects (U.S.

Only)  58

Reporting Safety Defects (Canada

Only)  59

Fuses

Fuse Specification Chart  60

Changing a Fuse  71

Maintenance

General Information  72

Under Hood Overview  73

Engine Oil Dipstick  75

Engine Oil Check  75

Engine Coolant Check  76

Automatic Transmission Fluid

Check  79

Brake Fluid Check  80

Power Steering Fluid Check  82

Fuel Filter  83

Changing the 12V Battery  83

Changing the Engine Air Filter  85

Wheels and Tires

Tire Care  91

Using Snow Chains  106

Changing a Road Wheel  107

Technical Specifications  110

Capacities and Specific-

ations

Engine Specifications  111

Motorcraft Parts  112

Vehicle Identification Number  113

Vehicle Certification Label  113

Transmission Code Designation  114

Technical Specifications  115

Extended Service Plan

(ESP)

Extended Service Plan (ESP)  119

Scheduled Maintenance

General Maintenance Information  121

Normal Scheduled Maintenance  124

Special Operating Conditions Scheduled

Maintenance  126

Scheduled Maintenance Record  128

Vehicle Care

General Information  87

Cleaning the Exterior  87

Cleaning the Engine  87

2

image24image25

Motorhome (TY3) , enUSA

image26image27

Introduction

image28

ABOUT THIS MANUAL

Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it.

WARNING

image29

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that

image30

you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

image31

Note: This manual describes product features and options available throughout the range of available models, sometimes even before they are generally available. It may describe options not fitted to your vehicle.

Note: Some of the illustrations in this manual may show features as used in different models, so may appear different to you on your vehicle. However, the essential information in the illustrations is always correct.

Note: Always use and operate your vehicle in line with all applicable laws and regulations.

Note: Pass on this manual when selling your vehicle. It is an integral part of the vehicle.

3

image32

Note: Either Ford Motor Company or an authorized Ford dealer may have originally sold this incomplete vehicle to a vehicle modifier who upfitted it. As a result, some of the options and features on this vehicle may differ from what we describe in this manual.

This manual may qualify the location of a component as left-hand side or right-hand side. The side is determined when facing forward in the seat.

image33

E154903

ARight-hand side B Left-hand side

Protecting the Environment

You must play your part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps toward this aim.

SYMBOLS GLOSSARY

These are some of the symbols you may see on your vehicle.

Safety alert

image34

See Owner’s Manual

image35image36

Motorhome (TY3) , enUSA

image37image38

Introduction

image39

Air conditioning system

image40

E162384

Anti-lock braking system

image41

Avoid smoking, flames or sparks

image42

Battery

image43

Battery acid

image44

Brake fluid – non petroleum

image45

based

Brake system

image46

Cabin air filter

image47

Check fuel cap

image48

Child safety door lock or unlock

image49

Child seat lower anchor

image50

Child seat tether anchor

image51

Cruise control

image52

E71340

Engine air filter

image53

Engine coolant

image54

Engine coolant temperature

image55

Engine oil

image56

Explosive gas

image57

Fan warning

image58

Fasten safety belt

image59

Front airbag

image60

Front fog lamps

image61

Fuel pump reset

image62

Fuse compartment

image63

Hazard warning flashers

image64

Heated rear window

image65

Do not open when hot  Heated windshield

image66image67

E91392 image68

Interior luggage compartment

image69

release

4

image70image71

Motorhome (TY3) , enUSA

image72image73

Introduction

image74

Jack

image75

Keep out of reach of children

image76

E161353

Lighting control

image77

Low tire pressure warning

image78

Maintain correct fluid level

image79

Note operating instructions

image80

Panic alarm

image81

Parking aid

image82

E139213

Parking brake

image83

Power steering fluid

image84

Power windows front/rear

image85

Power window lockout

image86

Service engine soon

image87

Side airbag

image88image89

Shield the eyes

image90

Stability control

image91

Windshield wash and wipe

image92

CALIFORNIAPROPOSITION65

WARNING

image93

Some constituents of engine exhaust, certain vehicle components, certain fluids contained in vehicles

image94

and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

image95

PERCHLORATE

Certain components in your vehicle such as airbag modules, safety belt pretensioners and remote control batteries may contain perchlorate material. Special handling may apply for service or vehicle end of life disposal. For more information visit:

image96

Web Address

www.dtsc.ca.gov/hazardouswaste/

perchlorate

FORD CREDIT

(U.S. Only)

Ford Credit offers a full range of financing and lease plans to help you acquire your vehicle. If you have financed or leased your vehicle through Ford Credit, thank you for your business.

5

image97

Motorhome (TY3) , enUSA

image98image99

Introduction

image100

For your convenience we offer a number of ways to contact us, as well as to help manage your account.

Phone: 1-800-727-7000

For more information regarding Ford Credit, as well as to access Account Manager, please go to www.fordcredit.com.

REPLACEMENT PARTS RECOMMENDATION

Your vehicle has been built to the highest standards using quality parts. We recommend that you demand the use of genuine Ford and Motorcraft parts whenever your vehicle requires scheduled maintenance or repair. You can clearly identify genuine Ford and Motorcraft parts by looking for the Ford, FoMoCo or Motorcraft branding on the parts or their packaging.

Scheduled Maintenance and Mechanical Repairs

One of the best ways for you to make sure that your vehicle provides years of service is to have it maintained in line with our recommendations using parts that conform to the specifications detailed in this Owner’s Manual. Genuine Ford and Motorcraft parts meet or exceed these specifications.

Collision Repairs

We hope that you never experience a collision, but accidents do happen. Genuine Ford replacement collision parts meet our stringent requirements for fit, finish, structural integrity, corrosion protection and dent resistance. During vehicle

6

image101

development we validate these parts deliver the intended level of protection as a whole system. A great way to know for sure you are getting this level of protection is to use genuine Ford replacement collision parts.

Warranty on Replacement Parts

Genuine Ford and Motorcraft replacement parts are the only replacement parts that benefit from a Ford Warranty. Damage caused to your vehicle as a result of the failure of non-Ford parts may not be covered by the Ford Warranty. For additional information, refer to the terms and conditions of the Ford Warranty.

SPECIAL NOTICES

New Vehicle Limited Warranty

For a detailed description of what is covered and what is not covered by your vehicle’s New Vehicle Limited Warranty, refer to the Warranty Manual that is provided to you along with your Owner’s Manual.

Special Instructions

For your added safety, your vehicle is fitted with sophisticated electronic controls.

WARNINGS

image102

Failure to follow the specific warnings and instructions could result in personal injury.

image103

Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active

image104

passenger airbag.

image105image106

Motorhome (TY3) , enUSA

image107image108

Introduction

image109

MOBILE COMMUNICATIONS EQUIPMENT

Using mobile communications equipment is becoming increasingly important in the conduct of business and personal affairs. However, you must not compromise your own or others’ safety when using such equipment. Mobile communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits. Mobile communication equipment includes, but is not limited to, cellular phones, pagers, portable email devices, text messaging devices and portable two-way radios.

WARNING

image110

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that

image111

you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

image112

EXPORT UNIQUE OPTIONS

For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this Owner’s Manual. A market unique supplement may be supplied that complements this book. By referring to the market unique supplement, if provided, you can properly identify those features, recommendations and specifications that

are unique to your vehicle. This Owner’s Manual is written primarily for the U.S. and Canadian Markets. Features or equipment listed as standard may be different on units built for Export. Refer to this Owner’s

Manual for all other required information and warnings.

7

image113image114

Motorhome (TY3) , enUSA

image115image116

Steering Wheel

image117

ADJUSTING THE STEERING

WHEEL

WARNING

image118

Do not adjust the steering wheel

image119

when your vehicle is moving.

image120image121

image122image123 2

image124image125

1

E161517

1.Pull and hold the steering wheel release lever.
2.Adjust the steering wheel to the desired position then release the lever.

CRUISE CONTROL

image126

E161518

See Cruise Control (page 35).

8

image127image128

Motorhome (TY3) , enUSA

image129image130

Wipers and Washers

image131

WINDSHIELD WIPERS

Note: Fully defrost the windshield before switching on the windshield wipers.

Note: Make sure the windshield wipers are switched off before entering a car wash.

Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that doesn’t resolve the issue, install new wiper blades.

Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield.

image132

Press the end of the stalk to activate the washer.

A brief press causes a single wipe without washer fluid.
A quick press and hold causes the wipers to swipe three times with washer fluid.
A long press and hold will activate the wipers and washer fluid for up to 10 seconds.

image133

E161462

E161461

Rotate the end of the control:

away from you to increase the wiper speed
toward you to decrease the wiper speed

WINDSHIELD WASHERS

Note: Do not operate the wipers on a dry

windshield. This may scratch the glass,

damage the wiper blades or cause the wiper

motor to burn out. Always use the

windshield washer before wiping a dry

windshield.

Note: Do not operate the washers when

the washer reservoir is empty. This may

cause the washer pump to overheat.

9

image134image135

Motorhome (TY3) , enUSA

image136image137

Lighting

image138

LIGHTING CONTROL

image139

A

P image140image141 B

C

E161456

AOff
BParking lamps, instrument panel lamps, license plate lamps and tail lamps
CHeadlamps

High Beams

image142

Headlamp Flasher

image143

E161458

Pull the lever toward you slightly and release it to flash the headlamps.

INSTRUMENT LIGHTING DIMMER

Note: If you disconnect the battery or it becomes discharged, the dimmer switch will require re-calibration. Rotate the dimmer switch from the full dim position to the full dome/on position to reset.

Note: Move the control to the full upright position, past detent, to turn on the interior lamps.

image144

E161457

Push the lever forward to switch the high beams on.

Push the lever forward again or pull the lever toward you to switch the high beams off.

image145

E161459

Move the control up or down to adjust the intensity of the panel lighting.

10

image146

Motorhome (TY3) , enUSA

image147image148

Lighting

image149

DAYTIME RUNNING LAMPS (If

Equipped)

WARNING

image150

Always remember to switch your headlamps on in low light situations or during inclement weather. The

image151

system does not activate the tail lamps and may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

image152

The system switches the low beam headlamps on at a reduced intensity in daylight conditions.

To switch the system on, switch the ignition on, and switch the lighting control to the off, autolamp or parking lamp position.

DIRECTION INDICATORS

image153

E161460

Push the lever up or down to use the

direction indicators.

Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change.

11

image154image155

Motorhome (TY3) , enUSA

image156image157

Instrument Cluster

image158

GAUGES

A  B

G

E161505

C  D  E

image159

F

AEngine oil pressure gauge B Tachometer

C Information display

DSpeedometer.
ETransmission fluid temperature gauge F Engine coolant temperature gauge G Fuel gauge

Engine Oil Pressure Gauge

Indicates engine oil pressure. The needle should stay in the normal operating range (between L and H). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked by your authorized dealer.

Speedometer

Indicates vehicle speed. Vehicle speed is limited to either 65 mph (105 km/h) or 75 mph (120 km/h).

Transmission Fluid Temperature Gauge

Normal area

The transmission fluid is within the normal operating temperature (between H and C).

12

image160image161

Motorhome (TY3) , enUSA

image162image163

Instrument Cluster

image164

Yellow area

The transmission fluid is higher than normal operating temperature. This can be caused by special operation conditions (i.e. snowplowing, towing or off-road use). Operating the transmission for extended periods of time with the gauge in the yellow area may cause internal transmission damage. Altering the severity of the driving conditions is recommended to lower the transmission temperature into the normal range.

Red area

The transmission fluid is overheating. Stop the vehicle to allow the temperature to return to normal range.

If the gauge is operating in the yellow or red area, stop the vehicle and verify the airflow is not restricted such as snow or debris blocking airflow through the grill. If the gauge continues to show high temperatures, see your authorized dealer.

Engine Coolant Temperature Gauge

image165

Fuel Gauge

Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when your vehicle is moving or on a gradient. The arrow adjacent to the fuel pump symbol indicates on which side of the vehicle the fuel filler door is located.

WARNING LAMPS AND INDICATORS

The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information.

Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle.

Anti-Lock Braking System

WARNING

Never remove the coolant reservoir cap while the engine is running or hot.

image166image167

At normal operating temperature, the needle will remain in the center section.

Note: Do not restart the engine until the cause of overheating has been resolved.

If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down.

13

image168

If it illuminates when you are driving, this indicates a

image169

malfunction. You will continue to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated. Have the system checked by your authorized dealer.

Battery

If it illuminates while driving, it

image170

indicates a malfunction. Switch off all unnecessary electrical

equipment and have the system checked by your authorized dealer immediately.

image171

Motorhome (TY3) , enUSA

image172image173

Instrument Cluster

image174

Brake System  Cruise Control (If Equipped)

Illuminates when you engage the parking brake with the ignition

image175

E144522  on.

If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer.

WARNING

image176

Illuminates when you switch this

feature on. See Using Cruise

E71340

Control (page 35).

image177

Direction Indicator

Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the

image178

indicators stay on or flash faster, check for a burned out bulb.

Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance

image179

may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury.

image180

Brake Reserve System (If Equipped)

Illuminates to indicate normal hydromax booster reserve

image181

E146190

system activation when the engine is off and the service brake pedal is applied.

This light may also illuminate momentarily if the engine is running and the driver turns the steering wheel fully in one direction while braking.

If the light remains on while the engine is running, this indicates inadequate hydraulic booster pressure or reserve pump system failure. Stop the vehicle as soon as possible and seek service immediately by your authorized dealer.

14

image182

Electronic Throttle Control

Illuminates when the engine has defaulted to a limp-home operation. See your authorized

image183

dealer as soon as possible.

Fasten Safety Belt

It will illuminate and a chime will sound to remind you to fasten your safety belt.

image184

High Beam

Illuminates when you switch the

image185

high beam headlamps on. It will flash when you use the

headlamp flasher.

Service Engine Soon

If the service engine soon

image186

indicator light stays illuminated after the engine is started, it

indicates that the On-Board Diagnostics (OBD-II) system has detected a malfunction of the vehicle emissions control system. Refer to On-Board Diagnostics (OBD-II) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 26).

image187

Motorhome (TY3) , enUSA

image188image189

Instrument Cluster

image190

If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

Note: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter or other vehicle components.

The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing.

Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 26).

Transmission Tow/Haul (If Equipped)

Illuminates when the tow/haul feature has been activated. If the

image191

E161509 light flashes steadily, have the system serviced immediately, damage to the transmission could occur.

Stage 1 is a single chime when the engine temperature begins to overheat.
Stage 2 is multiple chimes and engine power becomes limited in order to help cool the engine.
Stage 3 is multiple chimes and the engine will shut down.

Headlamps On Warning Chime

Sounds when you remove the key from the ignition and open the driver’s door and you have left the headlamps or parking lamps on.

Key in Ignition Warning Chime

Sounds when you open the driver’s door and you have left the key in the ignition with it in the off or accessory position.

Parking Brake On Warning Chime

Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately.

AUDIBLE WARNINGS AND

INDICATORS

Fail-Safe Cooling Warning Chime

Sounds when the coolant gauge pointer

has moved to hot. There are three stages

of chimes:

15

image192image193

Motorhome (TY3) , enUSA

image194image195

Information Displays

image196

GENERAL INFORMATION

WARNING

image197

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that

image198

you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

image199

Various systems on your vehicle can be controlled using the information display controls on the steering wheel.

Corresponding information is displayed in the information display.

Info

image200

E161507

Press the INFO button repeatedly to cycle through the following features:

TRIP

Registers the distance of individual journeys. Press and release the INFO button until the TRIP appears in the display. Press and hold the RESET button to reset

Information Display Controls

XXX° (outside air temperature)

E161506

image201

Press the info button to scroll through trip, outside air temperature, engine hours and miles to empty.
Press the setup button to scroll through various vehicle feature settings.
Press the reset button to choose settings, reset information and confirm messages.

16

image202

This displays the outside temperature.

MILES (km) TO E

This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to correctly detect the added fuel.

The DTE function will display a message in the information display when you have approximately 50 miles (80 km), to empty. Press RESET to clear this warning message. It will return at approximately 25 miles (40 km), 10 miles (16 km) and 0 miles (0 km) miles to empty.

DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km).

image203

Motorhome (TY3) , enUSA

image204image205

Information Displays

image206

ENG HRS

Registers the accumulated time the engine has been running.

System check and vehicle feature customization

ENGINE TEMP
TRANS TEMP
OIL PRESSURE
BRAKE FLUID LEVEL
FUEL LEVEL (if equipped)

E161508

image207

Press the SETUP button repeatedly to cycle the message center through the following features:

Note: When returning to the SETUP menu and a non-English language has been selected, HOLD RESET FOR ENGLISH will be displayed to change back to English. Press and hold the RESET button to change back to English.

PRESS RESET FOR SYS CHECK

When this message appears, press the RESET button and the message center will begin to cycle through the following systems and provide a status of the item if needed.

Note: Some systems show a message only if a condition is present

17

image208

UNITS

Displays the current units English or Metric

Press the RESET button to change from English to Metric.

ENGLISH RESET FOR NEW

Allows you to choose which language the message center will display in. Selectable languages are English, Spanish, or French.

Press the RESET button to cycle the message center through English, Spanish and French language choices. Press and hold the RESET button for two seconds to set the language choice.

INFORMATION MESSAGES

Note: Depending on the vehicle options equipped with your vehicle, not all of the messages will display or be available.

Certain messages may be abbreviated or shortened depending upon which cluster type you have.

Press the RESET button to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time.

Certain messages need to be confirmed before you can access the menus.

image209

Motorhome (TY3) , enUSA

image210image211

Information Displays

image212

Engine

image213

Message

Action

REDUCED ENGINE POWER

The engine is overheating. Stop your vehicle as soon

as safely possible, turn off the engine. If the warning

stays on followed by an indicator chime or continues

to come on, contact an authorized dealer as soon as

possible. Never remove the coolant reservoir cap while

the engine is running or hot.

STOP ENGINE SAFELY

The engine is overheating. Stop your vehicle as soon

as safely possible, turn off the engine. If the warning

stays on followed by an indicator chime or continues

to come on, contact an authorized dealer as soon as

possible.

CHECKENGINETEMPERATURE

The engine coolant is overheating. Stop your vehicle

as soon as safely possible, turn off the engine and let

it cool. Check the coolant and coolant level. If the

warning stays on or continues to come on, contact an

authorized dealer as soon as possible.

FUEL LEVEL LOW

A early reminder of a low fuel condition.

Maintenance

image214

Message

Action

LOW OIL PRESSURE

The engine oil pressure is low. Check the level of the

engine oil. If the oil level is OK and this warning persists,

shut down the engine immediately and contact an

authorized dealer as soon as possible. See Engine Oil

Check (page 75).

BRAKE FLUID LEVEL LOW

The brake fluid level is low and the brake system

should be inspected immediately. See Brake Fluid

Check (page 80).

CHECK FUEL CAP

The fuel cap is loose, not seated properly or off. Stop

your vehicle when convenient, turn off the engine and

check that you inserted the fuel cap is properly. Rotate

the cap until you hear a click. The warning message

switch off after a proper drive cycle is completed. See

Emission Control System (page 26). If the warning

message remains on or continues to comes back on,

see an authorized dealer as soon as possible.

18

image215image216

Motorhome (TY3) , enUSA

image217image218

Information Displays

image219

Transmission

image220

Message

Action

CHECK TRANS TEMPERATURE

The transmission fluid is overheating. This warning

may appear when towing heavy loads or when driving

in a low gear at a high speed for an extended period

of time. Stop your vehicle as soon as safely possible,

turn off the engine and let the transmission cool.

19

image221image222

Motorhome (TY3) , enUSA

image223image224

Starting and Stopping the Engine

image225

GENERAL INFORMATION  IGNITION SWITCH

WARNINGS

C

D

Extended idling at high engine

speeds can produce very high

E

temperatures in the engine and

exhaust system, creating the risk of fire or

B

other damage.

image226

Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up

image227image228

the engine compartment and exhaust system, creating the risk of fire.

Do not start the engine in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always

image229

open the garage door before you start the engine.

If you smell exhaust fumes inside your vehicle, have your vehicle checked by an authorized dealer

image230

immediately. Do not drive your vehicle if you smell exhaust fumes.

image231

If you disconnect the battery, your vehicle may exhibit some unusual driving characteristics for approximately 5 miles (8 kilometers) after you reconnect it. This is because the engine management system must realign itself with the engine. You can disregard any unusual driving characteristics during this period.

The powertrain control system meets all Canadian interference-causing equipment standard requirements regulating the impulse electrical field or radio noise.

When you start the engine, avoid pressing the accelerator pedal before and during operation. Only use the accelerator pedal when you have difficulty starting the engine.

20

image232

A

E161572

A (accessory) – Allows the electrical accessories, such as the radio, to operate while the engine is not running.

Note: Do not leave the ignition key in this position for too long. This could cause your vehicle battery to lose charge.

B (lock) – Locks the gearshift lever and allows key removal.

C (off) – The ignition is off.

Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge.

D (on) – All electrical circuits are operational and the warning lamps and indicators illuminate.

E (start) – Cranks the engine.

STARTING A GASOLINE ENGINE

When you start the engine, the idle speed increases, this helps to warm up the engine. If the engine idle speed does not slow down automatically, have your vehicle checked by an authorized dealer.

image233

Motorhome (TY3) , enUSA

image234image235

Starting and Stopping the Engine

image236

Before starting the engine check the following:

Make sure all occupants have fastened their safety belts.
Make sure the headlamps and electrical accessories are off.
Make sure the parking brake is on.
Move the transmission selector lever to position P.
Turn the ignition key to the on position. Note: Do not touch the accelerator pedal.
1.Fully press the brake pedal.
2.Turn the key to the start position to start the engine. Release the key when the engine starts.

Note: The engine may continue cranking for up to 15 seconds or until it starts.

Note: If you cannot start the engine on the first try, wait for a short period and try again.

Stopping the Engine When Your Vehicle is Moving

WARNING

image237

Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance.

image238

The steering will not lock, but higher effort will be required. When the ignition is switched off, some electrical circuits, warning lamps and indicators may also be off.

image239

1.Move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop.
2.When your vehicle has stopped, move the transmission selector lever to position P and turn the key to the off position.
3.Apply the parking brake.

Failure to Start  Guarding Against Exhaust Fumes

If you cannot start the engine after three attempts, wait 10 seconds and follow this procedure:

1.Fully press the brake pedal.
2.Fully press the accelerator pedal and hold it there.
3.Start the engine.

Stopping the Engine When Your Vehicle is Stationary

1.Move the transmission selector lever to position P.
2.Turn the key to the off position.
3.Apply the parking brake.

image240

WARNING

image241

If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer

image242

immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects.

image243

Important Ventilating Information

If you stop your vehicle and the leave the engine idling for long periods of time, we recommend that you do one of the following:

Open the windows at least 1 inch (2.5 centimeters)
Set your climate control to outside air.

21

image244

Motorhome (TY3) , enUSA

image245image246

Fuel and Refueling

image247

SAFETY PRECAUTIONS

WARNINGS

image248

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray

image249

and fire.

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel

image250

until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

Automotive fuels can cause serious injury or death if you misuse or mishandle them.

image251

Fuel ethanol and gasoline may contain benzene, which is a cancer-causing agent.

image252

When refueling always shut the engine off and never allow sparks or open flames near the filler neck.

image253

Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.

The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if you pump

image254

fuel into an ungrounded fuel container.

image255

Observe the following guidelines when handling automotive fuel:

22

image256

Extinguish all smoking materials and any open flames before refueling your vehicle.
Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours.
Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.
Avoid getting fuel liquid in your eyes. If you splash fuel in your eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.
Fuels can also be harmful if absorbed through the skin. If you splash fuel on your skin, clothing or both, promptly remove contaminated clothing and wash your skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation.
Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism.

Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If you splash fuel on your skin, promptly wash your skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.

image257

Motorhome (TY3) , enUSA

image258image259

Fuel and Refueling

image260

FUEL QUALITY

Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may not be covered under warranty.

Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as Regular with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended.

Choosing the Right Fuel

Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 15% ethanol in your gasoline vehicle. If your vehicle is a Flex Fuel Vehicle (FFV), it will have a yellow bezel placed over the fuel fill inlet.

Do not use:

fuels containing more than 15% ethanol or E-85 fuel
fuels containing methanol
fuels containing metallic based additives, including manganese-based compounds
fuels containing the octane booster additive, methylcyclopentadienyl manganese tricarbonyl (MMT)
leaded-fuel (The use of leaded fuel is prohibited by law)

Note: Use of any fuel other than the recommended fuel can cause powertrain damage, impair the emission control system or cause loss of vehicle performance. Any damage to the vehicle that is caused by the use of fuel not recommended will not be covered under warranty.

Octane Recommendations

image261

Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage.

RUNNING OUT OF FUEL

Avoid running out of fuel because this situation may have an adverse effect on powertrain components.

If you have run out of fuel:

You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. With keyless ignition, just start the engine. Crank time will be longer than usual.
Normally, adding 1 gallon (3.8 liters) of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than 1 gallon (3.8 liters) may be required.
The service engine soon indicator may come on. For more information on the service engine soon indicator, See

Warning Lamps and Indicators (page 13).

E161513

23

image262image263

Motorhome (TY3) , enUSA

image264image265

Fuel and Refueling

image266

REFUELING

WARNINGS

image267

Fuel vapor burns violently and a fuel fire can cause severe injuries.

image268

Read and follow all the instructions on the pump island.

image269

Turn off your engine when you are refueling.

image270

Do not smoke if you are near fuel or refueling your vehicle.

image271

Keep sparks, flames and smoking materials away from fuel.

image272

Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle. This is

image273

against the law in some places.

Keep children away from the fuel pump; never let children pump fuel.

image274

Do not use personal electronic devices while refueling.

image275

Wait at least 10 seconds before removing the fuel pump nozzle to allow any residual fuel to drain into

image276

the fuel tank.

Stop refueling after the fuel pump nozzle automatically shuts off for the second time. Failure to follow this

image277

will fill the expansion space in the fuel tank and could lead to fuel overflowing.

Do not remove the fuel pump nozzle from its fully inserted position when refueling.

image278image279

Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container:

Place approved fuel container on the ground.
Do not fill a fuel container while it is in the vehicle (including the cargo area).
Keep the fuel pump nozzle in contact with the fuel container while filling.
Do not use a device that would hold the fuel pump handle in the fill position.

Fuel Filler Cap

WARNINGS

image280

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel

image281

until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel

image282

system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.

image283

Note: If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford, Motorcraft or other certified fuel filler cap is not used.

Your fuel tank filler cap has an indexed design with a 1/4th turn on and off feature. When fueling your vehicle:

1.Put your vehicle in park (P).
2.Switch the engine off.
3.Carefully turn the filler cap counterclockwise until it spins off.
4.Pull to remove the cap from the fuel filler pipe.

24

image284image285

Motorhome (TY3) , enUSA

image286image287

Fuel and Refueling

image288

5.To install the cap, align the tabs on the cap with the notches on the filler pipe.
6.Turn the filler cap clockwise 1/4 of a turn clockwise until it clicks at least once.

If the Check Fuel Cap light or a Check Fuel Cap message appears in the instrument cluster and stays on after you start the engine, you may not have installed the fuel filler properly.

If the fuel cap light remains on, at the next opportunity, safely pull off of the road, remove the fuel filler cap, align the cap properly and reinstall it. The check fuel cap light or Check fuel cap message may not reset immediately. It may take several driving cycles for the indicators to turn off. A driving cycle consists of an engine start-up (after four or more hours with the engine off) followed by normal city and highway driving.

FUEL CONSUMPTION

Empty reserve is the amount of fuel remaining in the tank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range.

The usable capacity of the fuel tank is the amount of fuel that can be added into the tank after the gauge indicates empty
The advertised capacity is the total fuel tank size. See Capacities and Specifications (page 111). It is the combined usable capacity plus the empty reserve.
Due to the empty reserve, you may not be able to refuel the full amount of the advertised capacity of the fuel tank even when the fuel gauge reads empty.

25

image289

Filling the Tank

For consistent results when filling the fuel tank:

Turn the ignition off before fueling; an inaccurate reading results if the engine is left running.
Use the same fill rate (low-medium-high) each time the tank is filled.
Allow no more than two automatic click-offs when filling.

Results are most accurate when the filling method is consistent.

Calculating Fuel Economy

Do not measure fuel economy during the first 1000 miles (1600 kilometers) of driving (this is your engine’s break-in period); a more accurate measurement is obtained after 2000 miles – 3000 miles (3200 kilometers – 4800 kilometers). Also, fuel expense, frequency of fill ups or fuel gauge readings are not accurate ways to measure fuel economy.

1.Fill the fuel tank completely and record the initial odometer reading.
2.Each time you fill the tank, record the amount of fuel added.
3.After at least 3 to 5 tank fill ups, fill the fuel tank and record the current odometer reading.
4.Subtract your initial odometer reading from the current odometer reading.
5.Calculate fuel economy by dividing miles traveled by gallons used (For Metric: Multiply liters used by 100, then divide by kilometers traveled).

image290

Motorhome (TY3) , enUSA

image291image292

Fuel and Refueling

image293

Keep a record for at least 1 month and record the type of driving (city or highway). This provides an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter show how temperature impacts fuel economy. In general, lower temperatures mean lower fuel economy.

Conditions

Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
Carrying unnecessary weight may reduce fuel economy (approximately

1 mpg [0.4 km/L] is lost for every 400 pounds [180 kilograms] of weight carried).

Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski racks) may reduce fuel economy.
Using fuel blended with alcohol may lower fuel economy.
Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 kilometers) of driving.
Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.
Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal.
Close windows for high speed driving.

EMISSION CONTROL SYSTEM

WARNINGS

image294

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the

image295

engine compartment and exhaust system, which can start a fire.

Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If

image296

you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.

image297

Your vehicle is equipped with various emission control components and a catalytic converter that will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly:

Use only the specified fuel listed.
Avoid running out of fuel.
Do not turn off the ignition while your vehicle is moving, especially at high speeds.
Have the items listed in scheduled maintenance information performed according to the specified schedule.

The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system.

If you use parts other than Ford, Motorcraft or Ford-authorized parts for maintenance replacements, or for service of components affecting emission control, such non-Ford parts should be the equivalent to genuine Ford Motor Company parts in performance and durability.

26

image298image299

Motorhome (TY3) , enUSA

image300image301

Fuel and Refueling

image302

Illumination of the service engine soon indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate that the emission control system is not working properly.

An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately.

Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal also lists engine displacement

Please consult your warranty information for complete details.

On-Board Diagnostics (OBD-II)

Your vehicle is equipped with an on-board diagnostics system (OBD-II) that monitors the engine’s emission control system. This system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD-II system also assists your authorized dealer in properly servicing your vehicle.

When the service engine soon

image303

indicator illuminates, the OBD-II system has detected a

malfunction. Temporary malfunctions may cause the service engine soon indicator to illuminate.

Examples of temporary malfunctions are:

27

image304

the vehicle has run out of fuel—the engine may misfire or run poorly
poor fuel quality or water in the fuel—the engine may misfire or run poorly
the fuel fill inlet may not have been properly closed See Refueling (page 24).
driving through deep water—the electrical system may be wet.

You can correct these temporary malfunctions by filling the fuel tank with good quality fuel, properly closing the fuel fill inlet or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions present, the service engine soon indicator should stay off the next time you start the engine. A driving cycle consists of a cold engine startup followed by mixed city/highway driving. No additional vehicle service is required.

If the service engine soon indicator remains on, have your vehicle serviced at the first available opportunity. Although some malfunctions detected by the OBD-II may not have symptoms that are apparent, continued driving with the service engine soon indicator on can result in increased emissions, lower fuel economy, reduced engine and transmission smoothness, and lead to more costly repairs.

Readiness for

Inspection/Maintenance (I/M)

Testing

Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.

image305

Motorhome (TY3) , enUSA

image306image307

Fuel and Refueling

image308

If the service engine soon

image309

indicator is on or the bulb does not work, you may need to have

the vehicle serviced. See On-Board Diagnostics (OBD-II).

Your vehicle may not pass the I/M test if the service engine soon indicator is on or not working properly (bulb is burned out), or if the OBD-II system has determined that some of the emission control systems have not been properly checked. In this case, your vehicle is not ready for I/M testing.

If the vehicle’s engine or transmission has just been serviced, or the battery has recently run down or been replaced, the OBD-II system may indicate that the vehicle is not ready for I/M testing. To determine if the vehicle is ready for I/M testing, turn the ignition key to the on position for 15 seconds without cranking the engine. If the service engine soon indicator blinks eight times, it means that the vehicle is not ready for I/M testing; if the service engine soon indicator stays on solid, it means that the vehicle is ready for I/M testing.

The OBD-II system monitors the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, you may need to perform the following driving cycle consisting of mixed city and highway driving:

Drive on an expressway or highway for a steady 15 minutes, followed by 20 minutes of stop-and-go driving with at least four 30-second idle periods.

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. If the vehicle is still not ready for I/M testing, you will have to repeat the above driving cycle.

28

image310image311

Motorhome (TY3) , enUSA

image312image313

Transmission

image314

AUTOMATIC TRANSMISSION

WARNINGS

image315

Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition

image316

to the off position and remove the key whenever you leave your vehicle.

Do not apply the brake pedal and accelerator pedal simultaneously. Applying both pedals simultaneously

image317

for more than three seconds will limit engine rpm, which may result in difficulty maintaining speed in traffic and could lead to serious injury.

image318

Understanding the Positions of Your Automatic Transmission

PRND321

This learning process could take several transmission upshifts and downshifts; during this learning process, slightly firmer shifts may occur. After this learning process, normal shift feel and shift scheduling will resume.

Putting your vehicle in or out of gear:

1.Fully press down the brake pedal.
2.Move the gearshift lever into the desired gear.
3.Come to a complete stop.
4.Move the gearshift lever and securely latch it in P (Park)

P (Park)

This position locks the transmission and prevents the rear wheels from turning. Come to a complete stop before putting your vehicle into and out of P (Park)

R (Reverse)

E161511

This vehicle is equipped with an adaptive transmission shift strategy. Adaptive transmission shift strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected. The adaptive transmission shift strategy allows the transmission to relearn these operating parameters.

29

image319

With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse).

N (Neutral)

With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position.

D (Overdrive) with tow/haul off

D (Overdrive) with tow/haul off is the normal driving position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through gears one through five.

image320

Motorhome (TY3) , enUSA

image321image322

Transmission

image323

D (Overdrive) with tow/haul on    Positive vehicle acceleration (natural

acceleration from driving on a decline)

is sensed.

  Nearly all pressure is released from the

accelerator pedal.

image324

E161510

image325

The tow/haul feature improves transmission operation when towing a trailer or a heavy load. All transmission gear ranges are available when using tow/haul.

To activate tow/haul, press the button on the end of the

image326

E161509 gearshift lever. The TOW HAUL indicator light will illuminate in the instrument cluster.

Tow/haul delays upshifts to reduce frequency of transmission shifting. Tow/haul also provides engine braking in all forward gears when the transmission is in the D (Overdrive) position; this engine braking will slow the vehicle and assist the driver in controlling the vehicle when descending a grade. Depending on driving conditions and load conditions, the transmission may downshift, slow the vehicle and control the vehicle speed when descending a hill, without the accelerator pedal being pressed. The amount of downshift braking provided will vary based upon the amount the brake pedal is pressed.

Grade braking downshifts occur automatically when all three of the following occur:

30

image327

A minimum amount of time has expired since the last grade braking downshift.

Grade braking downshift mode is immediately exited if the Tow/Haul mode is deactivated or if the accelerator pedal is depressed beyond a minimum threshold.

To deactivate the tow/haul feature and return to normal driving mode, press the button on the end of the gearshift lever. The TOW HAUL light will no longer be illuminated.

When you shut-off and restart the engine, the transmission will automatically return to normal D (Overdrive) mode (tow/haul off).

WARNING

image328

Do not use the tow/haul feature when driving in icy or slippery conditions as the increased engine

image329

braking can cause the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control.

image330

3 (Third)

Transmission starts and operates in third gear only

Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking.

2 (Second)

Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades.

image331

Motorhome (TY3) , enUSA

image332image333

Transmission

image334

1 (First)

Provides maximum engine braking
Allows upshifts by moving gearshift lever
The transmission will not downshift into 1 (First) at high speeds; it will downshift to a lower gear and then shift into 1 (First) when the vehicle reaches slower speeds.

Forced downshifts

Allowed in D (Overdrive) with the tow/haul feature on or off
Press the accelerator to the floor
Allows transmission to select an appropriate gear

Brake-Shift Interlock

WARNINGS

image335

Do not drive your vehicle until you verify that the brake lamps are working.

image336

If your brake lamps are not working properly or if you have disconnected the vehicle battery cables, the

image337

vehicle brake lamps and hazard flashers may not properly warn traffic of a vehicle breakdown or approaching danger, which can increase the risk of serious injury or death. To minimize the risk of serious injury or death, be aware of your surroundings, use other hazard signaling devices if available, and move the vehicle to a safe location away from traffic as soon as possible.

When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll

image338

freely. To avoid unwanted vehicle movement, always fully set the parking brake prior to doing this procedure. Use wheel chocks if appropriate.

image339

31

WARNINGS

image340

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be

image341

working properly. See your authorized dealer.

image342

Your vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) unless the brake pedal is pressed.

If you cannot move the gearshift lever out of P (Park) position with the ignition in the 4 (on) position and the brake pedal pressed, a malfunction may have occurred. It is possible that a fuse has blown or the vehicle’s brake lamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter. If the fuses and brake lamps are working properly, and the vehicle still will not shift out of (P) Park, see your authorized dealer for service.

In an emergency, to disable the malfunctioning brake-shift interlock feature in order to shift the vehicle from P (Park) follow these steps:

1.Apply the parking brake. Turn key to the lock position, and then remove the key.
2.Disconnect the negative (black) battery cable from the battery.
3.Insert the key and turn to the off position. Shift to N (Neutral).
4.Reconnect the negative (black) battery cable to the battery.
5.Start the vehicle.

Note: See your authorized dealer as soon as possible if this procedure is used.

image343

Motorhome (TY3) , enUSA

image344image345

Transmission

image346

If Your Vehicle Gets Stuck In Mud or Snow

Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur.

Note: Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat.

If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear.

32

image347image348

Motorhome (TY3) , enUSA

image349image350

Brakes

image351

GENERAL INFORMATION

Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and should be inspected by an authorized dealer. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized dealer.

Note: Brake dust may accumulate on the wheels, even under normal driving conditions. Some dust is inevitable as the brakes wear and does not contribute to brake noise. See Cleaning the Alloy Wheels (page 88).

See the Instrument Cluster chapter for information on the

image352

E144522

brake system warning light.

Wet brakes result in reduced braking efficiency. Gently press the brake pedal a few times when driving from a car wash or standing water to dry the brakes.

Brake Over Accelerator

In the event the accelerator pedal becomes stuck or entrapped, apply steady and firm pressure to the brake pedal to slow the vehicle and reduce engine power. If you experience this condition, apply the brakes and bring your vehicle to a safe stop. Turn the engine off, shift to position P and apply the parking brake, and then inspect the accelerator pedal for any interferences. If none are found and the condition persists, have your vehicle towed to the nearest authorized dealer.

Hydraulic brake booster system (Hydroboost or Hydromax)

The Hydroboost and Hydromax systems receive fluid pressure from the power steering pump to provide power assist during braking.

33

image353

The Hydromax booster receives backup pressure from the reserve system electric pump whenever the fluid in the power steering system is not flowing. When the engine is off, the pump will turn on if the brake pedal is applied, or if the ignition is turned to the on position.

The sound of the pump operating may be heard by the driver, but this is a normal characteristic of the system.

The reserve system provides reduced braking power, so the vehicle should be operated under these conditions with caution, and only to seek service repair and remove the vehicle from the roadway.

Note: For Hydromax-equipped vehicles operating under normal conditions, the noise of the fluid flowing through the booster may be heard whenever the brake is applied. This condition is normal. Vehicle service is not required.

If braking performance or pedal response becomes very poor, even when the pedal is strongly pressed, it may indicate the presence of air in the hydraulic system or leakage of fluid. Stop the vehicle safely as soon as possible and seek service immediately.

HINTS ON DRIVING WITH ANTI-LOCK BRAKES

Note: When the system is operating, the brake pedal will pulse and may travel further. Maintain pressure on the brake pedal. You may also hear a noise from the system. This is normal.

The anti-lock braking system will not eliminate the risks when:

You drive too closely to the vehicle in front of you.
Your vehicle is hydroplaning.

image354

Motorhome (TY3) , enUSA

image355image356

Brakes

image357

You take corners too fast.
The road surface is poor.

PARKING BRAKE

WARNING

image358

Always set the parking brake fully

image359

and make sure the transmission

selector lever is placed in position P. Failure to set the parking brake and engage park could result in vehicle roll-away, property damage or bodily injury. Turn the ignition to the lock position and remove the key whenever you leave your vehicle.

image360

Apply the parking brake whenever your

vehicle is parked. Press the pedal

downward to set the parking brake.

The brake warning lamp in the

image361

instrument cluster illuminates

E144522 when the ignition is turned on until the parking brake is released.

The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the transmission mounted parking brake assembly, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.

To release the parking brake:

1.Press your foot brake pedal firmly.
2.Pull the parking brake release lever.

34

image362image363

Motorhome (TY3) , enUSA

image364image365

Cruise Control

image366

PRINCIPLE OF OPERATION

Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. You can use cruise control when your vehicle speed is greater than 20 mph (30 km/h).

USING CRUISE CONTROL

WARNINGS

image367

Do not use cruise control in heavy traffic, on winding roads or when the road surface is slippery. This could

image368

result in loss of vehicle control, serious injury or death.

When you are going downhill, your vehicle speed may increase above the set speed. The system will not

image369

apply the brakes. Change down a gear to assist the system in maintaining the set speed. Failure to do so could result in loss of vehicle control, serious injury or death.

image370

Note: Cruise control will disengage if your vehicle speed decreases more than 10 mph (16 km/h) below your set speed while driving uphill.

image371

E161518

The cruise controls are located on the steering wheel.

The indicator will display in the instrument cluster.

image372

E71340

Setting a Speed

1.Accelerate to the desired speed.
2.Press and release SET ACCEL.
3.Take your foot off the accelerator pedal.

Changing the Set Speed

Press and hold SET ACCEL to increase or COAST to decrease the set speed. Release the control when you reach the desired speed.
Press and release SET ACCEL to increase or COAST to decrease. The set speed will change in approximately 1 mph (2 km/h) increments.
Press the accelerator or brake pedal until you reach the desired speed. Press and release SET ACCEL.

Canceling the Set Speed

Tap the brake pedal. The set speed will not erase.

Resuming the Set Speed Press and release RES.

Switching Cruise Control Off

Note: You will erase the set speed if you switch the system off.

Press and release OFF or switch the ignition off.

Switching Cruise Control On

Press and release ON.

35

image373image374

Motorhome (TY3) , enUSA

image375image376

Load Carrying

image377

LOAD LIMIT

Vehicle Loading – with and without a Trailer

This section will guide you in the proper loading of your vehicle, trailer or both, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with

image378

CARGO

image379

the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Tire Label or Safety Compliance Certification Label:

Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment.

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment.

image380

E143817

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) including vehicle curb weight and all payload.

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label. The label shall be affixed to either the door hinge

36

image381image382

Motorhome (TY3) , enUSA

image383image384

Load Carrying

image385

pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position. The total load on each axle must never exceed its

image386

GVW

image387

Gross Axle Weight Rating.

Note: For trailer towing information refer to the RV and Trailer Towing Guide available at an authorized dealer.

image388

E143818

GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight, plus cargo, plus passengers.

GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). It is shown on the

Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position. The Gross Vehicle

Weight must never exceed the Gross Vehicle Weight Rating.

37

image389image390

Motorhome (TY3) , enUSA

image391image392

Load Carrying

image393

Example only:

image394

E142523

image395

E142524

WARNING

image396

Exceeding the Safety

image397

Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission or structural damage, serious damage to the vehicle, loss of control and personal injury.

image398

38

image399image400

Motorhome (TY3) , enUSA

image401image402

Load Carrying

image403image404

GCW  image405 GVW

image406

E143819

GCW (Gross Combined Weight)

is the Gross Vehicle Weight plus the weight of the fully loaded trailer.

GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer, including all cargo and passengers, that the vehicle can handle without risking damage. (Important: The towing vehicle’s braking system is rated for operation at Gross Vehicle Weight Rating, not at Gross Combined Weight Rating.) Separate functional brakes should be used for safe control of towed vehicles and for trailers where the Gross Combined Weight of the towing vehicle plus the trailer exceed the Gross Vehicle Weight Rating of the towing vehicle. The

Gross Combined Weight must never exceed the Gross Combined Weight Rating.

Maximum Loaded Trailer Weight – is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a vehicle with mandatory options, driver and front passenger weight (150 pounds [68 kilograms] each), no cargo weight (internal

or external) and a tongue load of 10–15% (conventional trailer). Consult an authorized dealer (or the RV and Trailer Towing Guide available at an authorized dealer) for more detailed information.

WARNINGS

image407

Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification

image408

Label.

Do not use replacement tires with lower load carrying

image409

capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GAWR limitations.

Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle

image410

and/or personal injury.

image411

Steps for determining the correct load limit:

39

image412image413

Motorhome (TY3) , enUSA

image414image415

Load Carrying

image416

1.Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.” on your vehicle’s placard.
2.Determine the combined weight of the driver and passengers that will be riding in your vehicle.
3.Subtract the combined weight of the driver and passengers from XXX kg or XXX lb.
4.The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lb. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400-750 (5 x 150) =
650lb.)
5.Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
6.If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.

Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.

The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity:

*Suppose your vehicle has a 1400-pound (635-kilogram) cargo and luggage capacity. You decide to go golfing. Is there enough load capacity to carry you, four of your friends and all the golf bags? You and four friends average 220 pounds (99 kilograms) each and the golf bags weigh approximately 30 pounds (13.5 kilograms) each. The calculation would be: 1400 – (5 x 220) – (5 x 30) = 1400 – 1100

150 = 150 pounds. Yes, you have enough load capacity in your vehicle to transport four friends and your golf bags. In metric units, the calculation would be: 635 kilograms – (5 x 99 kilograms) – (5 x 13.5 kilograms) = 635 – 495 – 67.5 = 72.5 kilograms.

*Suppose your vehicle has a 1400-pound (635-kilogram) cargo and luggage capacity. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past two years. Measuring the inside of the vehicle with the rear seat folded down, you have room for twelve 100-pound

(45-kilogram) bags of cement. Do you have enough load capacity to transport the cement to your home? If you and your friend each weigh 220 pounds (99 kilograms), the calculation would be: 1400 – (2 x 220) – (12 x 100) = 1400 – 440

1200 = – 240 pounds. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would

40

image417image418

Motorhome (TY3) , enUSA

image419image420

Load Carrying

image421

be: 635 kilograms – (2 x 99 kilograms) – (12 x 45 kilograms) = 635 – 198 – 540 = -103 kilograms. You will need to reduce the load weight by at least 240 pounds (104 kilograms). If you remove three 100-pound (45-kilogram) cement bags, then the load calculation would be:1400 – (2 x

220)– (9 x 100) = 1400 – 440 –

900 = 60 pounds. Now you have the load capacity to transport the cement and your friend home. In metric units, the calculation would be: 635 kilograms – (2 x 99 kilograms) – (9 x 45 kilograms) = 635 – 198 – 405 = 32 kilograms.

The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle Weight Rating specified for your vehicle on the Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position.

Special Loading Instructions for Owners of Pick-up Trucks and Utility-type Vehicles

WARNING

image422

Loaded vehicles may handle differently than unloaded

image423

vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.

image424

Your vehicle can haul more cargo and people than most passenger cars. Depending upon the type and placement of the load, hauling cargo and people may raise the center of gravity of the vehicle.

41

image425image426

Motorhome (TY3) , enUSA

image427image428

Towing

image429

TOWING A TRAILER

WARNINGS

image430

Do not exceed the GVWR or the GAWR specified on the

image431

certification label.

Towing trailers beyond the maximum recommended gross trailer weight exceeds the

image432

limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.

image433

Load Placement

To help minimize how trailer movement affects your vehicle when driving:

Load the heaviest items closest to the trailer floor.
Load the heaviest items centered between the left and right side trailer tires.
Load the heaviest items above the trailer axles or just slightly forward toward the trailer tongue. Do not allow the final trailer tongue weight to go above or below 10-15% of the loaded trailer weight.

Your vehicle may have electrical items, such as fuses or relays, related to towing. See the Fuses chapter.

Your vehicle’s load capacity designation is by weight, not by volume, so you cannot necessarily use all available space when loading a vehicle.

Towing a trailer places an extra load on your vehicle’s engine, transmission, axle, brakes, tires and suspension. Inspect these components periodically during, and after, any towing operation.

Select a tow bar with the correct rise or drop. When both the loaded vehicle and trailer are connected, the trailer frame should be level, or slightly angled down toward your vehicle, when viewed from the side.

When driving with a trailer or payload, a slight takeoff vibration or shudder may be present due to the increased payload weight. Additional information regarding proper trailer loading and setting your vehicle up for towing is located in another chapter of this manual. See Load Limit (page 36). You can also find the information in the RV & Trailer Towing Guide, available at an authorized dealer.

42

image434image435

Motorhome (TY3) , enUSA

image436image437

Towing

image438

RECOMMENDED TOWING WEIGHTS

Note: Do not exceed the trailer weight for your vehicle configuration listed in the chart below.

Note: Make sure to take into consideration trailer frontal area. Do not exceed 60 feet2 (5.6

meters2) trailer frontal area.

Note: For high altitude operation, reduce the gross combined weight by 2% per 1000 feet (300 meters) starting at the 1000 foot (300 meter) elevation point.

Note: Certain states require electric trailer brakes for trailers over a specified weight. Be sure to check state regulations for this specified weight. The maximum trailer weights listed may be limited to this specified weight, as the vehicle’s electrical system may not include the wiring connector needed to activate electric trailer brakes.

Your vehicle may tow a trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your vehicle configuration on the following chart.

Rear axle

Maximum

Maximum

Maximum trailer

ratio

GVWR

GCWR

weight

4.30

16000 lb (7257

23000 lb

7000 lb (3175 kg)

kg)

(10432 kg)

4.30

18000 lb (8165

23000 lb

5000 lb (2268 kg)

kg)

(10432 kg)

4.88

19500 lb

26000 lb

6500 lb (2894 kg)

(8845 kg)

(11793 kg)

5.38

20500 lb

26000 lb

5500 lb (2500 kg)

(9299 kg)

(11793 kg)

5.38

22000 lb

26000 lb

4000 lb (1814 kg)

(9979 kg)

(11793 kg)

6.17

24000 lb

30000 lb

6000 lb (2721 kg)

(10886 kg)

(13608 kg)

6.17

26000 lb

30000 lb

4000 lb (1814 kg)

(11793 kg)

(13608 kg)

image439

43

image440image441

Motorhome (TY3) , enUSA

image442image443

Towing

image444

ESSENTIAL TOWING CHECKS

Follow these guidelines for safe towing:

Do not tow a trailer until you drive your vehicle at least 1000 mi (1,600 km).
Consult your local motor vehicle laws for towing a trailer.
See the instructions included with towing accessories for the proper installation and adjustment specifications.
Service your vehicle more frequently if you tow a trailer. See your scheduled maintenance information.
If you use a rental trailer, follow the instructions the rental agency gives you.

Another chapter of this manual contains load specification terms found on the tire label and Safety Compliance label and instructions on calculating your vehicle’s load. See Load Limit (page 36).

Remember to account for the trailer tongue weight as part of your vehicle load when calculating the total vehicle weight.

Hitches

Do not use a hitch that either clamps onto the bumper or attaches to the axle.

Distribute the trailer load so 10-15% of the total trailer weight is on the tongue.

Weight-Distributing Hitches

WARNING

image445

Do not adjust a weight-distributing hitch to any position where the rear bumper of the vehicle is higher than

image446

it was before attaching the trailer. Doing so will defeat the function of the weight-distributing hitch, which may cause unpredictable handling, and could result in serious personal injury.

image447

44

image448

When hooking-up a trailer using a weight-distributing hitch, always use the following procedure:

1.Park the loaded vehicle, without the trailer, on a level surface.
2.Measure the height to the top of your vehicle’s front wheel opening on the fender. This is H1.
3.Securely attach the loaded trailer to your vehicle without the weight-distributing bars connected.
4.Measure the height to the top of your vehicle’s front wheel opening on the fender a second time. This is H2.
5.Install and adjust the tension in the weight-distributing bars so that the height of your vehicle’s front wheel opening on the fender is approximately halfway between H1 and H2.
6.Check that the trailer is level or slightly nose down toward your vehicle. If not, adjust the ball height accordingly and repeat Steps 1-6.
7.Lock the bar tension adjuster in place.
8.Check that the trailer tongue securely attaches and locks onto the hitch.
9.Install safety chains, lighting and trailer brake controls as required by law or the trailer manufacturer.

Safety Chains

Note: Never attach safety chains to the bumper.

Always connect the safety chains to the hook retainers of your vehicle hitch.

To connect the safety chains, cross them under the trailer tongue and allow enough slack for turning tight corners. Do not allow the chains to drag on the ground.

image449

Motorhome (TY3) , enUSA

image450image451

Towing

image452

Trailer Brakes

WARNING

image453

Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle

image454

may not have enough braking power and your chances of having a collision greatly increase.

image455

Electric brakes and manual, automatic or surge-type trailer brakes are safe if you install them properly and adjust them to the manufacturer’s specifications. The trailer brakes must meet local and federal regulations.

The rating for the tow vehicle’s braking system operation is at the gross vehicle weight rating, not the gross combined weight rating.

Separate functioning brake systems are required for safe control of towed vehicles and trailers weighing more than 1500 pounds (680 kilograms) when loaded.

Trailer Lamps

WARNING

image456

Never connect any trailer lamp wiring to the vehicle’s tail lamp wiring; this may damage the electrical system

image457

resulting in fire. Contact your authorized dealer as soon as possible for assistance in proper trailer tow wiring installation.

Additional electrical equipment may be required.

image458

Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, direction indicators and hazard lights are working.

Before Towing a Trailer

Practice turning, stopping and backing up to get the feel of your vehicle-trailer combination before starting on a trip. When turning, make wider turns so the trailer wheels clear curbs and other obstacles.

When Towing a Trailer

Do not drive faster than 70 mph

(113 km/h) during the first 500 mi

(800 km).

Do not make full-throttle starts.
Check your hitch, electrical connections and trailer wheel lug nuts thoroughly after you have traveled 50 mi (80 km).
When stopped in congested or heavy traffic during hot weather, place the gearshift in park (P) to aid engine and transmission cooling and to help air conditioning performance.
Switch off the speed control with heavy loads or in hilly terrain. The speed control may turn off automatically when you are towing on long, steep grades.
Shift to a lower gear when driving down a long or steep hill. Do not apply the brakes continuously, as they may overheat and become less effective.
If your transmission is equipped with a Grade Assist or Tow/Haul feature, use this feature when towing. This provides engine braking and helps eliminate excessive transmission shifting for optimum fuel economy and transmission cooling.
Allow more distance for stopping with a trailer attached. Anticipate stops and brake gradually.
Avoid parking on a grade. However, if you must park on a grade:
1.Turn the steering wheel to point your vehicle tires away from traffic flow.

45

image459image460

Motorhome (TY3) , enUSA

image461image462

Towing

image463

2.  Set your vehicle parking brake.  TRANSPORTING THE VEHICLE

3. Place the automatic transmission in

park (P).

image464

4. Place wheel chocks in the front and

back of the trailer wheels. (Chocks not

included with vehicle.)

image465

Launching or Retrieving a Boat or

Personal Watercraft (PWC)

Note: Disconnect the wiring to the trailer

image466

before backing the trailer into the water.

Note: Reconnect the wiring to the trailer

after removing the trailer from the water.

When backing down a ramp during boat

launching or retrieval:

Do not allow the static water level to rise above the bottom edge of the rear bumper.
Do not allow waves to break higher than 6 in (15 cm) above the bottom edge of the rear bumper.

Exceeding these limits may allow water to enter vehicle components:

Causing internal damage to the components.
Affecting driveability, emissions and reliability.

Replace the rear axle lubricant anytime the rear axle has been submerged in water. Water may have contaminated the rear axle lubricant, which is not normally checked or changed unless a leak is suspected or other axle repair is required.

image467

46

E143886

image468

If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. When calling for a tow truck, let the operator know what kind of vehicle you have.

It is advisable to have your vehicle towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Vehicle damage may occur if towed incorrectly, or by any other means.

image469

Motorhome (TY3) , enUSA

image470image471

Towing

image472

Do not exceed a maximum distance of 50 miles (80 kilometers) and maximum speed of 35 mph (56 km/h) when towing your vehicle from the front with the rear wheels on the ground. If you must exceed the maximum distance or speed, a qualified technician must remove the driveshaft. This prevents transmission damage.

TOWING THE VEHICLE ON

FOUR WHEELS

Emergency Towing

If your vehicle becomes inoperable (without access to wheel dollies, car-hauling trailer, or flatbed transport vehicle), it can be flat-towed (all wheels on the ground, regardless of the powertrain and transmission configuration) under the following conditions:

Your vehicle is facing forward for towing in a forward direction.
Place the transmission in position N. If you cannot move the transmission into N, you may need to override it.
Maximum speed is 35 mph (56 km/h).
Maximum distance is 50 miles (80 kilometers).

47

image473image474

Motorhome (TY3) , enUSA

image475image476

Driving Hints

image477

BREAKING-IN

You need to break in new tires for approximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unusual driving characteristics.

Avoid driving too fast during the first 1000 miles (1600 kilometers). Vary your speed frequently and change up through the gears early. Do not labor the engine.

Do not tow during the first 1000 miles (1600 kilometers).

Avoid these actions; they reduce your fuel economy:

Sudden accelerations or hard accelerations.
Revving the engine before turning it off.
Idle for periods longer than one minute.
Warm up your vehicle on cold mornings.
Use the air conditioner or front defroster.
Use the speed control in hilly terrain.
Rest your foot on the brake pedal while driving.

ECONOMICAL DRIVING

Drive a heavily loaded vehicle or tow a trailer.

Your fuel economy is affected by several things, such as how you drive, the conditions you drive under, and how you maintain your vehicle.

You may improve your fuel economy by keeping these things in mind:

Accelerate and slow down in a smooth, moderate fashion.
Drive at steady speeds without stopping.
Anticipate stops; slowing down may eliminate the need to stop.
Combine errands and minimize stop-and-go driving.
Close the windows for high-speed driving.
Drive at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]).
Keep the tires properly inflated and use only the recommended size.
Use the recommended engine oil.
Perform all regularly scheduled maintenance.

48

image478

Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost for every 400 lb [180 kilogram] of weight carried).
Driving with the wheels out of alignment.

Conditions

Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
Adding certain accessories to your vehicle (for example bug deflectors, rollbars, light bars, running boards, ski racks or luggage racks) may reduce fuel economy.
To maximize the fuel economy, drive with the tonneau cover installed (if equipped).
Using fuel blended with alcohol may lower fuel economy.
Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 kilometers) of driving.
Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.

image479

Motorhome (TY3) , enUSA

image480image481

Driving Hints

image482

Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal.
Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation.
Close the windows for high-speed driving.

DRIVING THROUGH WATER

Note: Driving through deep water above the recommended levels can cause vehicle damage.

If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).

image483

E142667

When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall.

Once through the water, always dry the brakes by moving your vehicle slowly while applying light pressure on the brake pedal. Wet brakes do not stop the vehicle as quickly as dry brakes.

49

image484image485

Motorhome (TY3) , enUSA

image486image487

Roadside Emergencies

image488

ROADSIDE ASSISTANCE

Vehicles Sold in the United States:

Getting Roadside Assistance

To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available:

24 hours a day, seven days a week.
For the coverage period listed on the Roadside Assistance Card included in your Owner’s Manual portfolio.

Roadside Assistance covers:

A flat tire change with a good spare, if provided with the vehicle (except vehicles supplied with a tire inflation kit).
Battery jump start.
Lock-out assistance (key replacement cost is the customer’s responsibility).
Fuel delivery — independent service contractors, if not prohibited by state, local or municipal law, shall deliver up to 2 gal (7.6 L) of gasoline or 5 gal

(18.9 L) of diesel fuel to a disabled vehicle. Roadside Assistance limits fuel delivery service to two no-charge occurrences within a 12-month period.

Winch out — available within 100 ft (30.5 m) of a paved or county maintained road, no recoveries.
Towing — Ford eligible vehicles towed to an authorized dealer within 35 mi (56 km) of the disablement location or to the nearest authorized dealer. If a member requests a tow to an authorized dealer that is more than 35 mi (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 mi (56 km).

image489

Roadside Assistance includes up to $200 for a towed trailer if the disabled eligible vehicle requires service at the nearest authorized dealer. If the towing vehicle is operational but the trailer is not, then the trailer does not qualify for any roadside services.

Vehicles Sold in the United States:

Using Roadside Assistance

Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is in the owner’s information portfolio in the glove compartment.

United States Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673.

If you need to arrange roadside assistance for yourself, Ford Motor Company reimburses a reasonable amount for towing to the nearest dealership within

35 mi (56 km). To obtain reimbursement information, United States Ford vehicle customers call 1-800-241-3673. Customers need to submit their original receipts.

Vehicles Sold in Canada: Getting Roadside Assistance

Canadian customers who require roadside assistance, call 1-800-665-2006.

Vehicles Sold in Canada: Using Roadside Assistance

For your convenience, you may complete the roadside assistance identification card found in the centerfold of your warranty guide and retain for future reference.

50

image490

Motorhome (TY3) , enUSA

image491image492

Roadside Emergencies

image493

Canadian roadside coverage and benefits may differ from the U.S. coverage. If you require more information, please refer to the coverage section of your warranty guide, call us in Canada at

1-800-665-2006, or visit our website at www.ford.ca.

Sykes Assistance Services Corporation administers the Roadside Assistance program. You must receive covered services in Canada or the continental United States. Coverage extends to vehicles that use public, non-seasonal, annually traveled roadways. Roadside Assistance coverage does not extend to vehicles involved in cross-country driving, logging, autocross and any other form of off-road use. Well maintained roads and surfaces help ensure safe travel for the supplier, and allow their representatives to perform service as per the standard operating procedures.

In Remote Locations

If our supplier cannot take your vehicle by road to the nearest authorized dealership, transportation by rail or water may be necessary. The program covers a tow to the dock or rail terminal and also to the dealership at the end of the trip.

For rail or water transportation, however, contact your authorized dealer to confirm if you are eligible for additional coverage before you authorize or pay for the service.

Call the Ford Roadside Assistance at 1-800-665-2006 for additional information.

HAZARDWARNINGFLASHERS

Note: The hazard warning flashers will operate when the ignition is in any position or if the key is not in the ignition. If used when the engine is not running, the battery will lose charge. As a result, there may be insufficient power to restart your engine.

image494

E161463

The hazard flasher control is located on the steering column, just behind the steering wheel. Use it when your vehicle is creating a safety hazard for other motorists.

Press the flasher control and all front and rear direction indicators flash.
Press the flasher control again to turn them off.

JUMPSTARTINGTHEVEHICLE

WARNINGS

image495

The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could

image496

result in personal injury or vehicle damage.

Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.

image497

Use only an adequate-sized cable with insulated clamps.

image498image499

51

image500image501

Motorhome (TY3) , enUSA

image502image503

Roadside Emergencies

image504

Preparing Your Vehicle

Note: Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage.

Note: Use only a 12-volt supply to start your vehicle.

Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system.

Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles do not touch. Turn all accessories off.

Connecting the Jumper Cables

WARNING

image505

Do not attach the cables to fuel lines, engine rocker covers, the intake manifold or electrical components

image506

as grounding points. Stay clear of moving parts. To avoid reverse polarity connections, make sure that you correctly identify the positive (+) and negative (-) terminals on both the disabled and booster vehicles before connecting the cables.

image507

Note: In the illustration, the bottom vehicle represents the booster vehicle.

1

image508

3

4

2

E142664

1.Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery.
2.Connect the other end of the positive

(+) cable to the positive (+) terminal of the assisting battery.

3.Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
4.Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, or connect the negative (-) cable to a ground connection point if available.

WARNING

image509

Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.

image510

A spark may cause an explosion of the

gases that surround the battery.

image511

52

image512image513

Motorhome (TY3) , enUSA

image514image515

Roadside Emergencies

image516

Jump Starting

1.Start the engine of the booster vehicle and rev the engine moderately, or press the accelerator gently to keep your engine speed between 2000 and 3000 rpms, as shown in your tachometer.
2.Start the engine of the disabled vehicle.
3.Once the disabled vehicle has been started, run both vehicle engines for an additional three minutes before disconnecting the jumper cables.

Removing the Jumper Cables

Remove the jumper cables in the reverse order that they were connected.

image517

2.Remove the jumper cable on the negative (-) terminal of the booster vehicle’s battery.
3.Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.
4.Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery.

After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the battery can recharge.

4

1

2

3

E142665

1.Remove the jumper cable from the ground metal surface or connecting point, if available.

53

image518image519

Motorhome (TY3) , enUSA

image520image521

Customer Assistance

image522

GETTING THE SERVICES YOU NEED

Warranty repairs to your vehicle must be performed by an authorized dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.

Please note that certain warranty repairs require special training and equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer.

A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft® parts, or remanufactured or other parts that are authorized by Ford.

Away From Home

If you are away from home when your vehicle needs service, contact the Ford Customer Relationship Center or use the online resources listed below to find the nearest authorized dealer.

In the United States:

Mailing address

Ford Motor Company

Customer Relationship Center

P.O. Box 6248

Dearborn, MI 48121

Telephone

1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952)

Online

Additional information and resources are available online at www.fordowner.com

54

image523

These are some of the items that can be found online:

U.S. dealer locator by Dealer Name, City/State or Zip Code.
Owner Manuals.
Maintenance Schedules.
Recalls.
Ford Extended Service Plans.
Ford Genuine Accessories.
Service specials and promotions. In Canada:

Mailing address

Customer Relationship Centre

Ford Motor Company of Canada, Limited

P.O. Box 2000

Oakville, Ontario L6K 0C8

Telephone

1-800-565-3673 (FORD)

Online

www.ford.ca

Twitter

@FordServiceCA (English Canada)

@FordServiceQC (Quebec)

Additional Assistance

If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps:

1.Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer.
2.If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager.
3.If you require assistance or clarification on Ford Motor Company policies, please contact the Ford Customer Relationship Center.

image524

Motorhome (TY3) , enUSA

image525image526

Customer Assistance

image527

In order to help us serve you better, please have the following information available when contacting a Customer Relationship Center:

Vehicle Identification Number.
Your telephone number (home and business).
The name of the authorized dealer and city where located.
The vehicle’s current odometer reading.

In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.

California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18000 miles (29 000 km), whichever occurs first:

1.Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR
2.Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle)

OR

3.The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time).

In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address:

Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126

IN CALIFORNIA (U.S. ONLY)

California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle.

55

image528

You are required to submit your warranty dispute to BBB AUTO LINE before asserting in court any rights or remedies conferred by California Civil Code Section 1793.22(b). You are also required to use BBB AUTO LINE before exercising rights or seeking remedies created by the Federal Magnuson-Moss Warranty Act, 15 U.S.C. sec. 2301 et seq. If you choose to seek redress by pursuing rights and remedies not created by California Civil Code Section 1793.22(b) or the Magnuson-Moss Warranty Act, resort to BBB AUTO LINE is not required by those statutes.

image529

Motorhome (TY3) , enUSA

image530image531

Customer Assistance

image532

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY)

Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step procedure outlined earlier in this chapter in the Getting the Services you need section, you may be eligible to participate in the BBB AUTO LINE program.

The BBB AUTO LINE program consists of two parts – mediation and arbitration. During mediation, a representative of the

Bwill contact both you and Ford Motor Company to explore options for settlement of the claim. If an agreement is not reached during mediation or you do not want to participate in mediation, and if your claim is eligible, you may participate in the arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing.

Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. You are not bound by the decision, and may reject the decision and proceed to court where all findings of the BBB Auto Line dispute, and decision, are admissible in the court action. Should you choose to accept the BBB AUTO LINE decision, Ford is then bound by the decision, and must comply with the decision within 30 days of receipt of your acceptance letter.

BAUTO LINE Application: Using the information provided below, please call or write to request a program application. You will be asked for your name and address, general information about your new vehicle, information about your warranty concerns, and any steps you have

already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines.

You can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to:

BBB AUTO LINE

3033 Wilson Boulevard, Suite 600

Arlington, Virginia 22201

BAUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673.

Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation.

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY)

For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).

The CAMVAP program is a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings.

56

image533image534

Motorhome (TY3) , enUSA

image535image536

Customer Assistance

image537

In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding on both you and Ford of Canada.

CAMVAP services are available in all Canadian territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685 or visit www.camvap.ca.

GETTING ASSISTANCE

OUTSIDE THE U.S. AND

CANADA

Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel.

If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact our Customer Relationship Center.

The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company or Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the United States.

57

image538

If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, Central America, the Caribbean, and Israel, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact:

FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A.

Telephone: (313) 594-4857

Fax: (313) 390-0804

Email: [email protected]

For customers in Guam, the Commonwealth of the Northern Mariana Islands (CNMI), America Samoa, and the U.S. Virgin Islands, please feel free to call our Toll-Free Number: (800) 841-FORD (3673).

If your vehicle must be serviced while you are traveling or living in Puerto Rico, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact:

FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A.

Telephone: (800) 841-FORD (3673)

FAX: (313) 390-0804 Email: [email protected] www.ford.com.pr

If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact:

image539

Motorhome (TY3) , enUSA

image540image541

Customer Assistance

image542

FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A.

Telephone: +971 4 3326084 Toll-Free Number of the Kingdom of Saudi Arabia: 800 8971409

Local Telephone Number of Kuwait:

24810575

FAX: +971 4 3327299 Email: [email protected] www.me.ford.com

If you buy your vehicle in North America and then relocate to any of the above locations, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations & Global Growth Initiatives by emailing [email protected]

If you are in another foreign country, contact the nearest authorized dealer. In the event your inquiry is unresolved, communicate your concern with the dealership’s Sales Manager, Service Manager or Customer Relations Manager. If you require additional assistance or clarification, please contact the respective Customer Relationship Center as previously listed.

Customers in the U.S. should call 1-800-392-3673.

ORDERING ADDITIONAL OWNER’S LITERATURE

To order the publications in this portfolio, contact Helm, Incorporated at:

HELM, INCORPORATED 47911 Halyard Drive Plymouth, Michigan 48170 Attention: Customer Service

Or to order a free publication catalog, call toll free: 1-800-782-4356

58

image543

Monday-Friday 8:00 a.m. – 6:00 p.m. EST

Helm, Incorporated can also be reached by their website:

www.helminc.com

(Items in this catalog may be purchased by credit card, check or money order.)

Obtaining a French Owner’s Manual

French Owner’s Manual can be obtained from your authorized dealer or by contacting Helm, Incorporated using the contact information listed previously in this section.

REPORTINGSAFETYDEFECTS (U.S. ONLY)

image544

E142557

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company.

image545

Motorhome (TY3) , enUSA

image546image547

Customer Assistance

image548

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to:

Administrator

1200 New Jersey Avenue, Southeast

Washington, D.C. 20590

image549

You can also obtain other

information about motor vehicle

safety from

http://www.safercar.gov.

REPORTINGSAFETYDEFECTS (CANADA ONLY)

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada.

Transport Canada Contact Information

image550 Website image551 http://www.tc.gc.ca/eng/roadsafety/menu.htm

image552 Phone image553 1–800–333–0510

59

image554image555

Motorhome (TY3) , enUSA

image556image557

Fuses

image558

FUSE SPECIFICATION CHART

Power Distribution Box

WARNINGS

image559

Always disconnect the battery before servicing high current fuses.

image560

To reduce risk of electrical shock, always replace the cover to the power distribution box before

image561

reconnecting the battery or refilling fluid reservoirs.

image562

Locate the power distribution box in the engine compartment. It has high-current fuses that protect your vehicle’s main electrical systems from overloads.

If the battery has been disconnected and reconnected, you will need to reset some features. See Changing the 12V Battery (page 83).

image563

E161519

image564

Fuse or relay number

Fuse amp rating

Protected components

1

5A*

Power brake assist module – Hydromax.

2

10A*

Air conditioning compressor clutch.

3

20A*

Air conditioning clutch relay coil.

Catalyst monitor sensor.

60

image565image566

Motorhome (TY3) , enUSA

image567image568

Fuses

image569

Fuse or relay number

Fuse amp rating

Protected components

Engine heated exhaust gas oxygen sensor

#11 and #21.

Mass air flow sensor with intake air

temperature.

Vapor management valve.

4

5A*

Powertrain control module memory.

Powertrain control module relay coil.

5

20A*

Powertrain control module power.

6

20A*

Instrument panel dimmer module.

Instrument panel fuse #41.

Park lamp feeds.

Trailer tow running lamp relay coil.

7

20A*

Ignition coils.

Radio capacitors.

8

30A*

Hydromax – Anti-lock brake system

module.

9

10A*

Powertrain control module.

Starter ground relay coil.

Starter main relay coil.

10

20A*

Daytime running lamps.

11

20A*

Fuel pump relay coil.

Powertrain control module power.

12

25A*

Instrument panel – backup lamp feed.

Trailer tow back-up lamps feed.

13

30A**

Trailer tow electric brake controller feed.

14

60A**

Instrument panel battery feed (fuse #9, 15,

21).

Lighting primary fuse.

15

20A**

Trailer tow park lamps.

16

60A**

Anti-lock brake system module –

Hydromax.

40A**

Anti-lock brake system module – Hydro-

boost.

17

20A**

Horn feed.

61

image570image571

Motorhome (TY3) , enUSA

image572image573

Fuses

image574

Fuse or relay number

Fuse amp rating

Protected components

18

20A**

Backup lamp feed.

Tow/haul switch.

Transmission control indicator light.

19

Not used.

20

30A**

Powertrain control module relay coil.

Powertrain control module relay (Power

distribution box fuses # 3, 5, 7, 18).

21

20A**

Fuel injectors.

Fuel pump motor.

22

20A**

Cigar lighter feed.

Diagnostic tool connector.

23

40A**

Blower motor feed.

24

50A**

Instrument panel battery feed (fuses #4,

10, 16, 22).

25

40A**

Ignition switch feed (Instrument panel

fuses #1, 5, 7, 11, 13, 14, 17, 19, 23; Power

distribution box fuses #9, 11).

26

40A**

Ignition switch feed (Instrument panel

fuses #5, 11, 17, 23, 26, 38).

27

30A**

Multi-function switch (headlamps).

28

30A**

Starter solenoid.

29

60A**

Power brake assist motor – Hydromax.

40A**

Anti-lock brake system module – Hydro-

boost.

R1

Air conditioning clutch relay.

R2

Fuel pump relay.

R3

Horn relay.

R4

Starter relay.

R5

Blower motor relay.

R6

Powertrain control module relay.

62

image575image576

Motorhome (TY3) , enUSA

image577image578

Fuses

image579image580

image581 Fuse or relay number image582 Fuse amp rating image583 Protected components

image584

Diode 1 image585image586 Fuel pump diode.

image587

Diode 2 image588image589 Air conditioning clutch diode.

image590

*Mini fuses.

**Maxi fuses.

UPS Power Distribution Box 1

image591

E172543

image592

Fuse or relay number

Fuse amp rating

Protected components

R1

Relay

Powertrain control module.

R2

Relay

Daytime running lamps.

R3

Relay

Starter motor.

R4

Relay

Blower motor.

R5

Relay

Horn.

R6

Relay

Fuel pump.

R7

Relay

Starter ground.

R8

Relay

Trailer tow parking lamps.

R9

Relay

Back-up lamps.

R10

Relay

Not used.

R11

Relay

Not used.

R12

Relay

Air conditioning.

63

image593image594

Motorhome (TY3) , enUSA

image595image596

Fuses

image597image598

Fuse or relay number

Fuse amp rating

Protected components

M1-1

10A

Hydromax brake on/off relay.

M1-2

Not used.

M1-3

Not used.

M1-4

Not used.

UPS Power Distribution Box 2

image599

E172544

image600

Fuse or relay number

Fuse amp rating

Protected components

M1

25A*

Back-up lamps.

M2

20A*

Daytime running lamps.

M3

30A*

4–channel anti-lock brake system module

(Hydromax).

M4

20A*

Powertrain control module run/start.

Fuel pump relay coil.

M5

10A*

Starter relay coil.

M6

20A*

Vehicle power 4.

M7

5A*

Hydromax motor monitor.

M8

20A*

Vehicle power 2.

M9

20A*

Vehicle power 1.

M10

10A*

Air conditioning.

64

image601image602

Motorhome (TY3) , enUSA

image603image604

Fuses

image605

Fuse or relay number

Fuse amp rating

Protected components

M11

5A*

Powertrain control module relay keep alive

power.

M12

20A*

Parking lamps.

D1

Diode

One-touch start.

D2

Diode

Fuel pump.

D3

Diode

Air conditioning.

R2-1

Not used.

J1

30A**

Powertrain control module vehicle power.

J2

20A**

Fuel pump.

J3

20A**

Cigar lighter power point.

Diagnostic connector.

J4

40A**

Blower motor.

J5

30A**

Headlamps.

J6

40A**

Ignition switch feeds.

J7

40A**

Ignition switch feeds.

J8

50A**

Instrument panel fuse box.

J9

30A**

Starter motor solenoid.

J10

40A**

3–channel anti-lock brake system module.

60A**

4–channel anti-lock brake system module

(Hydromax).

J11

30A**

Trailer tow electronic brake.

J12

60A**

Lighting.

J13

20A**

Vehicle power 3.

J14

20A**

Horn.

J15

40A**

3–channel anti-lock brake system module.

65

image606image607

Motorhome (TY3) , enUSA

image608image609

Fuses

image610image611

image612 Fuse or relay number image613 Fuse amp rating image614 Protected components

image615

60A**  image616 4–channel anti-lock brake system module. image617

image618

J16  image619 20A** image620 Trailer tow parking lamps.

*Mini fuse.

**J-case fuse.

Diode and Relay Module

Locate the module box with the power

distribution box in from of the radiator.

image621

E161520

image622

Relay location

Protected components

1

One-touch integrated start (ATO diode).

2

Not used.

3

Not used.

4

Daytime running lamps power relay.

5

Hydromax – brake on/off signal isolating relay.

6

Reverse lamps relay.

7

Starter ground relay.

8

Trailer tow parking lamps relay.

66

image623image624

Motorhome (TY3) , enUSA

image625image626

Fuses

image627

Fuse Holder Module  Locate the fuse holder next to the diode

and relay module.

image628

Fuse number image629 Fuse amp rating image630 Protected components

1  10A

Passenger Compartment Fuse Panel

Locate this fuse panel below and to the left of the steering wheel near the brake pedal. Remove the panel cover to access the fuses.

image631 Hydromax – brake on/off signal.

To remove a fuse, use the fuse panel cover’s fuse puller tool.

image632

E161521

image633

image634 Fuse or relay number image635 Fuse amp rating image636 Protected components

1  20A  Body builder rear direction indicator and

stop lamp feeds.

Direction indicators.

67

image637image638

Motorhome (TY3) , enUSA

image639image640

Fuses

image641

Fuse or relay number

Fuse amp rating

Protected components

Direction indicators and stop lamps.

2

Not used.

3

Not used.

4

10A

Instrument cluster.

5

10A

Body builder accessory feed (accessory

and run).

6

Not used.

7

15A

Blower motor relay coil.

8

10A

Brake lamps feed.

9

20A

Stop lamps: Vehicle direction indicators

and stop lamps, Body builder rear direction

indicators and stop feeds, Body builder

stop lamp feed.

10

10A

Instrument cluster memory.

11

30A

Wiper/washer module.

Wiper feed.

12

Not used.

13

10A

Anti-lock brake system module –

Hydromax.

14

10A

Anti-lock brake system module – Hydro-

boost.

Instrument cluster power.

Instrument cluster warning lamps.

Warning indicator module.

15

15A

Left-hand direction indicator feed.

16

20A

Body builder battery (+12V) feed.

17

5A

Body builder radio feed.

18

Not used.

19

5A

Daytime running lamps relays.

20

Not used.

21

15A

Right-hand direction indicator feed.

68

image642image643

Motorhome (TY3) , enUSA

image644image645

Fuses

image646

Fuse or relay number

Fuse amp rating

Protected components

22

20A

Trailer tow direction indicators.

23

10A

Cluster run/accessory.

24

Not used.

25

10A

Body builder right-hand low beam head-

lamp feed.

26

10A

Brake shift interlock actuator.

27

Not used.

28

Not used.

29

Not used.

30

Not used.

31

10A

Body builder left-hand low beam head-

lamp feed.

32

Not used.

33

10A

Reverse lamps.

34

10A

Body builder reverse gear.

Trailer tow reverse lamps.

35

20A

Body builder high beam feed.

High beam indicator.

36

Not used.

37

Not used.

38

10A

Body builder run feed.

39

Not used.

40

Not used.

41

10A

Instrument cluster lighting.

42

Not used.

43

Not used.

44

Not used.

Relay 1

Trailer tow right-hand direction indicator.

69

image647image648

Motorhome (TY3) , enUSA

image649image650

Fuses

image651

Fuse or relay number

Fuse amp rating

Relay 2

Relay 3

Relay 4

Relay 5

Relay 6

Relay 7

Diode 1

Diode 2

F1

F2

F3

F4

10A

F5

F6

F7

F8

F9

F10

F11

F12

image652

Protected components

image653 Trailer tow left-hand direction indicator.

image654 Right-hand direction indicator.

image655 Left-hand direction indicator.

image656 Not used.

Daytime running lamps.

Parking brake.

image657 Daytime running lamps on/off.

image658 Brake transmission shift interlock.

image659 Brake transmission shift interlock.

image660 Not used.

image661 Not used.

image662 Not used.

image663 Brake transmission shift interlock.

image664 Not used.

image665 Not used.

image666 Not used.

image667 Not used.

image668 Not used.

image669 Not used.

image670 Not used.

Not used.

70

image671

Motorhome (TY3) , enUSA

image672image673

Fuses

image674

CHANGING A FUSE

Fuses

WARNING

image675

Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and

image676

could start a fire.

image677

E142430

image678

If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components.

Standard Fuse Amperage Rating and Color

image679

Color

Fuse rating

Mini fuses

Standard

Maxi fuses

Cartridge

Fuse link

fuses

maxi fuses

cartridge

2A

Grey

Grey

3A

Violet

Violet

4A

Pink

Pink

5A

Tan

Tan

7.5A

Brown

Brown

10A

Red

Red

15A

Blue

Blue

20A

Yellow

Yellow

Yellow

Blue

Blue

25A

Natural

Natural

Natural

Natural

30A

Green

Green

Green

Pink

Pink

40A

Orange

Green

Green

50A

Red

Red

Red

60A

Blue

Yellow

Yellow

70A

Tan

Brown

80A

Natural

Black

Black

71

image680image681

Motorhome (TY3) , enUSA

image682image683

Maintenance

image684

GENERAL INFORMATION

Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialized tools developed specifically for servicing your vehicle.

To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. See Scheduled Maintenance (page 121).

If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your warranty information to find out which parts and services are covered.

Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft® parts are designed and built to provide the best performance in your vehicle.

Precautions

Do not work on a vehicle with the engine running in an enclosed space, unless you are sure you have enough ventilation.
Keep all open flames and other burning material (such as cigarettes) away from the battery and all fuel related parts.

Working with the Engine Off

1.Set the parking brake and shift to P (Park).
2.Turn off the engine and remove the key (if equipped).
3.Block the wheels.

Working with the Engine On

WARNING

image685

To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner

image686

removed and do not remove it while the engine is running.

image687

1.Set the parking brake and shift to P (Park).
2.Block the wheels
Do not work on a hot engine.
Make sure that nothing gets caught in moving parts.

72

image688image689

Motorhome (TY3) , enUSA

image690image691

Maintenance

image692

UNDER HOOD OVERVIEW

Motorhome chassis

image693

A

B C

D

E

F  G  H

E161549

A.Engine coolant reservoir
B.Engine oil filler cap
C.Automatic transmission fluid dipstick
D.Power distribution box
E.Air filter assembly
F.Engine oil dipstick
G.Brake fluid reservoir
H.Power steering fluid reservoir

73

image694image695

Motorhome (TY3) , enUSA

image696image697

Maintenance

image698

Commercial chassis

image699

A

B

C

D

E  F  G  H

E161550

A.Engine coolant reservoir
B.Engine oil filler cap
C.Automatic transmission fluid dipstick
D.Power distribution box
E.Engine oil dipstick
F.Brake fluid reservoir
G.Air filter assembly
H.Power steering fluid reservoir

74

image700image701

Motorhome (TY3) , enUSA

image702image703

Maintenance

image704

ENGINE OIL DIPSTICK

image705

A  B

E161560

AMIN B MAX

ENGINE OIL CHECK

Note: Check the level before starting the engine.

Note: Make sure that the level is between the MIN and the MAX marks.

1.Make sure that your vehicle is on level ground.
2.Turn the engine off and wait 10 minutes for the oil to drain into the oil pan.
3.Remove the dipstick and wipe it with a clean, lint-free cloth. Replace the dipstick and remove it again to check the oil level.

If the level is at the MIN mark, add oil immediately.

Adding Engine Oil

Note: Do not remove the filler cap when the engine is running.

Note: Do not add oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage.

75

image706

E142732

Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricants Specification Advisory Council (ILSAC), comprised of U.S. and Japanese automobile manufacturers.

1.Remove the filler cap.
2.Add engine oil that meets the Ford specifications. See Capacities and Specifications (page 111).
3.Replace the filler cap. Turn it until you feel a strong resistance.

Resetting the Oil Life Monitoring System

Note: Reset the oil life monitoring only after an oil change.

1.Turn the ignition key to the ON position. Do not start the engine. For vehicles with push-button start, press and hold the start button for two seconds without pressing the brake pedal. Do not attempt to start the engine.
2.Press both the accelerator and brake pedals at the same time.
3.Keep both pedals fully pressed.

image707

Motorhome (TY3) , enUSA

image708image709

Maintenance

image710

4.After three seconds, the Service: Oil reset in prog. message will be displayed.
5.After 25 seconds, the Service: Oil reset complete message will be displayed.
6.Release the accelerator and brake pedals, then rotate the key to the off position.

Note: The Service: Oil reset complete message will no longer be displayed.

ENGINE COOLANT CHECK

WARNINGS

image711

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling

image712

system can burn you badly. Also, spilling coolant on hot engine parts can burn you.

Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine

image713

coolant could make it difficult to see through the windshield.

To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure

image714

relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when you loosen the cap slightly.

Do not add coolant further than the MAX mark.

image715image716

When the engine is cold, check the concentration and level of the engine coolant at the intervals listed in the scheduled maintenance information. See Scheduled Maintenance (page 121).

Note: Make sure that the level is between the MIN and MAX marks on the coolant reservoir.

Note: Coolant expands when it is hot. The level may extend beyond the MAX mark

Note: If the level is at the MIN mark, below the MIN mark, or empty, add coolant immediately. See Adding Engine Coolant in this chapter.

The coolant concentration should be maintained within 48% to 50%, which equates to a freeze point between -30°F (-34°C) and -34°F (-37°C).

Note: For best results, coolant concentration should be tested with a refractometer such as Robinair Coolant and Battery Refractometer 75240. We do not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations.

Note: Automotive fluids are not interchangeable. Do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.

Adding Engine Coolant

Note: Do not use stop leak pellets, cooling system sealants, or additives as they can cause damage to the engine cooling or heating systems. Your vehicle’s warranty does not cover this damage.

76

image717image718

Motorhome (TY3) , enUSA

image719image720

Maintenance

image721

Do not mix different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants may harm the engine’s cooling system. The use of an improper coolant may harm the engine and cooling system components and may void the warranty. Use prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page 111).
In case of emergency, you can add a large amount of water without engine coolant in order to reach a vehicle service location. In this instance, you must have the cooling system drained, chemically cleaned with Motorcraft Premium Cooling System Flush, and refilled with engine coolant as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing.
Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant).

Alcohol and other liquids can cause engine damage from overheating or freezing.

Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant.

Unscrew the cap slowly. Any pressure will escape as you unscrew the cap.

Add prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page 111).

Whenever you add coolant, check the coolant level in the coolant reservoir the next few times you drive the vehicle. If necessary, add enough prediluted engine coolant to bring the coolant level to the proper level.

77

image722

Recycled Engine Coolant

Ford Motor Company does not recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available.

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.

Severe Climates

If you drive in extremely cold climates:

It may be necessary to have a Ford authorized dealer increase the coolant concentration above 50%.
A coolant concentration of 60% will provide improved freeze point protection. Engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage

If you drive in extremely hot climates:

It may be necessary to have a Ford authorized dealer decrease the coolant concentration to 40%.
A coolant concentration of 40% will provide improved overheat protection. Engine coolant concentrations below 40% will decrease the freeze and corrosion protection characteristics of the engine coolant and may cause engine damage.

Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection.

image723

Motorhome (TY3) , enUSA

image724image725

Maintenance

image726

What you Should Know About Fail-Safe Cooling

If you deplete the engine coolant supply, this feature allows you to drive your vehicle temporarily before you incur incremental component damage. The fail-safe distance depends on ambient temperatures, vehicle load and terrain.

How Fail-Safe Cooling Works

If the engine begins to overheat, the engine coolant temperature gauge will move to the red (hot) area and:

The coolant temperature warning indicator will light.

image727

The service engine soon indicator will light.

image728

If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine.

When this occurs, the vehicle will still operate. However:

The engine power will be limited.
This will disable the air conditioning system.

Continued operation will increase the engine temperature and the engine will completely shut down, causing steering and braking effort to increase.

Once the engine temperature cools, the engine can be re-started. Take your vehicle to an authorized dealer as soon as possible to minimize engine damage.

78

image729

When Fail-Safe Mode Is Activated

WARNINGS

image730

Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long

image731

as necessary to bring the vehicle to rest in a safe location and seek immediate repairs. When in fail-safe mode, the vehicle will have limited power, will not be able to maintain high-speed operation and may completely shut down without warning, potentially losing engine power, power steering assist and power brake assist, which may increase the possibility of a crash resulting in serious injury.

Never remove the coolant reservoir cap while the engine is running or hot.

image732image733

You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore:

1.Pull off the road as soon as safely possible and switch off the engine.
2.Have your vehicle towed to an authorized dealer.
3.If this is not possible, wait a short period for the engine to cool.
4.Check the coolant level and replenish if low.
5.Re-start the engine and take your vehicle to an authorized dealer.

Note: Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealer as soon as possible.

image734

Motorhome (TY3) , enUSA

image735image736

Maintenance

image737

AUTOMATIC TRANSMISSION FLUID CHECK

WARNING

image738

The dipstick cap and surrounding components may be hot; gloves are recommended.

image739image740

Note: Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 20 miles [30 km]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool to normal operating temperature 150°F – 170°F (66°C – 77°C) before checking.

Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes.

Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, (i.e., if the transmission slips or shifts slowly) or if you notice some sign of fluid leakage. To check the fluid level:

1.Drive the vehicle 20 miles (30 km) or until it reaches normal operating temperature
2.Park the vehicle on a level surface and engage the parking brake
3.With the engine running, parking brake engaged and your foot on the brake pedal, move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage
4.Latch the gearshift lever in P (Park) and leave the engine running.

79

image741

5.Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Under Hood Overview in this chapter for the location of the dipstick.
6.Install the dipstick making sure it is fully seated in the filler tube.
7.Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature.

Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.

Low fluid level

image742

E161551

Do not drive the vehicle if there is no indication of fluid on the dipstick and the ambient temperature is above 50°F (10°C).

Correct fluid level

image743

E161552

image744

Motorhome (TY3) , enUSA

image745image746

Maintenance

image747

The transmission fluid should be in this range if at normal operating temperature (150°F-170°F [66°C-77°C]).

The transmission fluid should be checked at normal operating temperature 150°F-170°F (66°C-77°C) on a level surface. The normal operating temperature can be reached after approximately 20 miles (30 km) of driving. You can check the fluid without driving if the ambient temperature is above 50°F (10°C). However, if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature

High fluid level

image748

E161554

image749

Add fluid in ½ pint (250 ml) increments through the filler tube until the level is correct.

Note: If an overfill occurs, excess fluid should be removed by an authorized dealer. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.

Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.

E161553

Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.

Adjusting automatic transmission fluid levels

Note: Use of a non-approved automatic transmission fluid may cause internal transmission damage. Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the transmission dipstick and also in the See Capacities and Specifications (page 111).

80

image750

Automatic transmission fluid filter

The TorqShift™ automatic transmission is equipped with a serviceable transmission fluid filter located inside the transmission bottom pan. Refer to the scheduled maintenance information for service intervals for the automatic transmission fluid and transmission filter. For transmission filter maintenance, see your authorized dealer.

BRAKE FLUID CHECK

Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately.

image751

Motorhome (TY3) , enUSA

image752image753

Maintenance

image754

Hydromax

WARNINGS

image755

Carefully read cautionary information on product label. For MEDICAL EMERGENCY INFORMATION contact

image756

a physician or Poison Control Center immediately; on Ford-Motorcraft™ products call: 1-800-959-3673 (FORD). Failure to follow these instructions may result in personal injury.

Use of any brake fluid other than that indicated for your brake system will cause permanent damage.

image757

Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail and result in personal

image758

injury.

image759

Chassis with gross vehicle weight ratings of 20500 pounds (9299 kilograms), 22000 pounds (9979 kilograms), 24000 pounds (10886 kilograms) and 26000 pounds (11793 kilograms) are equipped with Hydromax Brake Booster Systems and must use Motorcraft DOT 5.1 Motor Vehicle Brake Fluid or equivalent meeting Ford Specification ESD-M6C57-A. See Technical Specifications (page 115).

Add fluid up to the bottom of the rings located at the top of the reservoir. Do not fill above this line.

image760

E161555

81

image761

Use only DOT 5.1 brake fluid that is certified to meet Ford specifications.
A clear gel-like substance in the hydraulic brake master cylinder reservoir may appear on some vehicles. This substance is a silicone base lubricant used during assembly of the master cylinder. It will float on top of the brake hydraulic fluid in the master cylinder. This condition is normal and in no way affects the operation of the brake system. It does not require any service.
Brake system fluid should be replaced on a regular basis to maintain optimum braking performance, especially under heavy-duty driving conditions such as frequent steep grades or heavy towing loads. See Scheduled Maintenance (page 121).

Hydroboost

Chassis with gross vehicle weight ratings of 16000 pounds (7257 kilograms), 18000 pounds (8165 kilograms) and 19500 pounds (8845 kilograms) are equipped with Hydroboost Brake Booster Systems and must use Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid or equivalent meeting Ford Specification WSS-M6C62-A.

Add brake fluid from a clean unopened container until the level reaches MAX. Do not fill above this line. Use only DOT 3 brake fluid that is certified to meet Ford specifications.

Brake system fluid should be replaced on a regular basis to maintain optimum braking performance, especially under heavy-duty driving conditions such as frequent steep grades or heavy towing loads. See Scheduled Maintenance (page 121).

image762

Motorhome (TY3) , enUSA

image763image764

Maintenance

image765

Parking brake fluid

image766

E161556

POWER STEERING FLUID CHECK

A

image767

B

Note: Do not fill the parking brake through the vent plug (A) (located on top of the transmission).

Check the parking brake fluid level only if there is visible signs of fluid leakage. If necessary, fill the parking brake assembly to the bottom of the filler plug hole (B) (located on the driver side of the transmission). See Technical Specifications (page 115).

image768

E161557

Note: The power steering cap has both a cold and hot indicator on the dipstick.

1.Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
2.While the engine idles, turn the steering wheel left and right several times.
3.Turn the engine off.

82

image769

Motorhome (TY3) , enUSA

image770image771

Maintenance

image772

4.Check the fluid level on the dipstick. It should be between the arrows in the FULL range on the side of the dipstick with the words MAX. HOT at the top. Do not add fluid if the level is within this range.
5.If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the FULL range. Be sure to put the dipstick back in the reservoir.

Steering linkage lubrication points

image773

A

A

A

A

A

E161558

A

A  image774 A

There are nine lubrication points on the

steering linkage shown as “A”. See CHANGING THE 12V BATTERY Technical Specifications (page 115).

image775

WARNINGS

FUEL FILTER

Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed.

83

image776

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow

image777

flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and

image778

damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

image779

Motorhome (TY3) , enUSA

image780image781

Maintenance

image782

WARNINGS

image783

Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or

image784

clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

image785

Note: If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.

Note: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.

Your vehicle is equipped with a Motorcraft® maintenance-free battery which normally does not require additional water during its life of service.

For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.

If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water.

It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time.

84

image786

To ensure proper operation of the battery management system (BMS), any electrical devices that are added to the vehicle should not have their ground connection made directly at the negative battery post. A connection at the negative battery post can cause inaccurate measurements of the battery condition and potential incorrect system operation.

Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability and may also affect the performance of other electrical systems in the vehicle.

When a battery replacement is required, the battery should only be replaced with a Ford recommended replacement battery that matches the electrical requirements of the vehicle.

Note: Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.

Battery relearn

When the battery is disconnected or a new battery installed:

image787

Motorhome (TY3) , enUSA

image788image789

Maintenance

image790

The transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will not affect function or durability of the transmission. Over time the adaptive learning process will fully update transmission operation to its optimum shift feel.
The clock and the preset radio stations must be reset once the battery is reconnected.
Your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery, the engine must relearn its idle and fuel trim strategy.

When the battery is disconnected or a new battery is installed, begin the battery relearn process:

1.With the vehicle at a complete stop, set the parking brake.
2.Put the gearshift lever in P (Park), turn off all accessories and start the engine.
3.Run the engine until it reaches normal operating temperature.
4.Allow the engine to idle for at least one minute.
5.Turn the A/C on and allow the engine to idle for at least one minute.
6.Drive the vehicle to complete the relearning process.
The vehicle may need to be driven to relearn the idle and fuel trim strategy.

CHANGING THE ENGINE AIR FILTER

WARNING

image791

To reduce the risk of vehicle damage and personal burn injuries, do not start your engine with the air cleaner

image792

removed and do not remove it while the engine is running.

image793

Change the air filter element at the proper interval. See Scheduled Maintenance (page 121).

When changing the air filter element, use only the air filter element listed. See Capacities and Specifications (page 111).

Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used.

image794

E161559

1.Loosen the latches that secure the air filter cover in place.
2.Carefully separate the two halves of the air filter housing.
3.Remove the air filter element from the housing.
4.Wipe any dirt or debris from the air filter housing and cover.

85

image795image796

Motorhome (TY3) , enUSA

image797image798

Maintenance

image799

5.Install a new air filter element.
6.Replace the air filter cover to the housing and secure the latches. Be careful not to crimp the filter element edges between the air filter housing. This could cause filter damage and allow unmetered air to enter the engine if not properly seated.

86

image800image801

Motorhome (TY3) , enUSA

image802image803

Vehicle Care

image804

GENERAL INFORMATION  Exterior Chrome

Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes.

CLEANING THE EXTERIOR

Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash.

Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces.
Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Dry your vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting.
Immediately remove items such as gasoline, diesel fuel, bird droppings and insect deposits because they can cause damage to your vehicle’s paintwork and trim over time. Use Motorcraft Bug and Tar Remover.
Remove any exterior accessories, such as antennas, before entering a car wash.

Note: Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible.

Stripes or Graphics (if equipped)

Do not use a commercial or high-pressure sprayer on the surface or edge of stripes and graphics. This can cause damage to the film and cause the edge of the film to peel away from the vehicle surface.

87

image805

Note: Never use abrasive materials such as steel wool or plastic pads as they can scratch the chrome surface.

Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers

Wash your vehicle first, using cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash.
Use Motorcraft Custom Bright Metal Cleaner. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag.
Do not apply cleaning product to hot surfaces and do not leave cleaning product on chrome surfaces longer than the time recommended.
Using other non-recommended cleaners can result in severe and permanent cosmetic damage.

Underbody

Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt.

Cleaning Plastic Exterior Parts

Use only approved products to clean plastic parts

For routine cleaning, use Motorcraft Detail Wash.
If tar or grease spots are present, use Motorcraft Bug and Tar Remover.

CLEANING THE ENGINE

Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal.

image806

Motorhome (TY3) , enUSA

image807image808

Vehicle Care

image809

When washing:

Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.
Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components.
Spray Motorcraft Engine Shampoo and Degreaser on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo.
Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage.
Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations.
Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine.

CLEANING THE ALLOY

WHEELS (If Equipped)

Note: Do not apply a cleaning chemical to warm or hot wheel rims and covers.

Note: Some automatic car washes may cause damage to the finish on your wheel rims and covers.

Note: Industrial-strength or heavy-duty cleaners in combination with brush agitation to remove brake dust and dirt, could wear away the clear coat finish over a period time.

Note: Do not use hydrofluoric acid-based or high caustic-based wheel cleaners, steel wool, fuels or strong household detergents.

Note: If you intend parking your vehicle for an extended period after cleaning the wheels with a wheel cleaner, drive your vehicle for a few minutes before doing so. This will reduce the risk of increased corrosion of the brake discs.

Alloy wheels and wheel covers are coated with a clear coat paint finish. To maintain their condition we recommend that you:

Clean the wheels weekly using Motorcraft Wheel and Tire Cleaner. Apply using manufacturer’s instructions.
Use a sponge to remove heavy deposits of dirt and brake dust accumulation.
Rinse thoroughly with a strong stream of water when you have completed the cleaning process.
To remove tar and grease, use Motorcraft Bug and Tar Remover.

VEHICLE STORAGE

If you plan on storing your vehicle for 30 days or more, read the following maintenance recommendations to make sure your vehicle stays in good operating condition.

We engineer and test all motor vehicles and their components for reliable, regular driving. Under various conditions, long-term storage may lead to degraded engine performance or failure unless you use specific precautions to preserve engine components.

General

Store all vehicles in a dry, ventilated place.
Protect from sunlight, if possible.
If vehicles are stored outside, they require regular maintenance to protect against rust and damage.

88

image810image811

Motorhome (TY3) , enUSA

image812image813

Vehicle Care

image814

Body

Wash your vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear-wheel housing and the underside of front fenders.
Periodically wash your vehicle if it is stored in exposed locations.
Touch-up exposed or primed metal to prevent rust.
Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration. Re-wax as necessary when you wash your vehicle.
Lubricate all hood, door and trunk lid hinges, and latches with a light grade oil.
Cover interior trim to prevent fading.
Keep all rubber parts free from oil and solvents.

Cooling system

Protect against freezing temperatures.
When removing your vehicle from storage, check coolant fluid level. Confirm that there are no cooling system leaks and that fluid is at the recommended level.

Battery

Check and recharge as necessary. Keep connections clean.
If storing your vehicle for more than 30 days without recharging the battery, we recommend that you disconnect the battery cables to maintain battery charge for quick starting.

Note: It is necessary to reset memory features if battery cables are disconnected.

Brakes

Engine

The engine oil and filter should be changed prior to storage because used engine oil contains contaminates that may cause engine damage.
Start the engine every 15 days for a minimum of 15 minutes. Run at fast idle with the climate controls set to defrost until the engine reaches normal operating temperature.
With your foot on the brake, shift through all the gears while the engine is running.
We recommend that you change the engine oil before you use your vehicle again.

Fuel system

Fill the fuel tank with high-quality fuel until the first automatic shutoff of the fuel pump nozzle.

89

image815

Make sure the brakes and parking brake release fully.

Tires

Maintain recommended air pressu