2017 Ford Expedition Owners Manual

image1

owner.ford.com  ford.ca

September 2016

Second Printing

Owner’s Manual

Expedition

image2

Litho in U.S.A.

image3

2017 EXPEDITION Owner’s Manual

HL1J 19A321 AA

image4image5The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted.

© Ford Motor Company 2016

All rights reserved.

Part Number: 201604 20160810134553

image6image7

image8image9

Table of Contents

image10

Introduction

About This Manual  7

Symbols Glossary  7

Data Recording  9

California Proposition 65  11

Perchlorate  11

Ford Credit  11

Replacement Parts

Recommendation  12

Special Notices  12

Mobile Communications

Equipment  13

Export Unique Options  13

Environment

Protecting the Environment  15

Child Safety

General Information  16

Installing Child Restraints  17

Booster Seats  24

Child Restraint Positioning  26

Child Safety Locks  27

Seatbelts

Principle of Operation  29

Fastening the Seatbelts  30

Seatbelt Height Adjustment  32

Seatbelt Warning Lamp and Indicator

Chime  33

Seatbelt Reminder  33

Child Restraint and Seatbelt

Maintenance  35

Seatbelt Extension  35

Supplementary Restraints

System

Principle of Operation  36

Driver and Passenger Airbags  37

Side Airbags  38

image11

1

Safety Canopy™  39

Crash Sensors and Airbag Indicator  40

Airbag Disposal  41

Keys and Remote Controls

Principle of Operation  42

General Information on Radio

Frequencies  42

Remote Control  43

Replacing a Lost Key or Remote

Control  46

MyKey™

Principle of Operation  47

Creating a MyKey  48

Clearing All MyKeys  49

Checking MyKey System Status  50

Using MyKey With Remote Start

Systems  51

MyKey Troubleshooting  51

Doors and Locks

Locking and Unlocking  52

Manual Liftgate  54

Power Liftgate  56

Keyless Entry  58

Security

Passive Anti-Theft System  61

Anti-Theft Alarm  62

Power Running Boards

Using Power Running Boards  63

Steering Wheel

Adjusting the Steering Wheel – Vehicles

With: Column Shift/Manual Adjustable

Steering Column  65

Adjusting the Steering Wheel – Vehicles

With: Floor Shift/Manual Adjustable

Steering Column  65

image12

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image13image14

Table of Contents

image15

Adjusting the Steering Wheel – Vehicles

With: Power Adjustable Steering

Column  66

Audio Control  67

Voice Control  68

Cruise Control  69

Information Display Control  69

Heated Steering Wheel  69

Pedals

Adjusting the Pedals  70

Wipers and Washers

Windshield Wipers  71

Autowipers  71

Windshield Washers  72

Rear Window Wiper and Washers  72

Lighting

General Information  73

Lighting Control  73

Autolamps – Vehicles With:

Autolamps  74

Instrument Lighting Dimmer  75

Daytime Running Lamps  75

Front Fog Lamps  76

Direction Indicators  76

Interior Lamps  77

Ambient Lighting  78

Windows and Mirrors

Power Windows  79

Exterior Mirrors  80

Interior Mirror  81

Childminder Mirror  81

Rear Quarter Windows  82

Sun Visors  82

Moonroof  82

image16

2

Instrument Cluster

Gauges  84

Warning Lamps and Indicators  87

Audible Warnings and Indicators  90

Information Displays

General Information  91

Information Messages  102

Climate Control

Manual Climate Control  112

Manual Climate Control – Vehicles With:

Electronic Manual Temperature

Control (EMTC)  113

Automatic Climate Control  115

Hints on Controlling the Interior

Climate  116

Rear Passenger Climate Controls  119

Heated Windows and Mirrors  120

Remote Start  120

Seats

Sitting in the Correct Position  121

Head Restraints  121

Manual Seats  123

Power Seats  124

Memory Function  125

Rear Seats  126

Heated Seats  133

Climate Controlled Seats  134

Universal Garage Door

Opener

Universal Garage Door Opener  136

Auxiliary Power Points

Auxiliary Power Points  141

Storage Compartments

Center Console  143

image17

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image18image19

Table of Contents

image20

Overhead Console  143

Starting and Stopping the

Engine

General Information  144

Ignition Switch  144

Keyless Starting  144

Steering Wheel Lock  145

Starting a Gasoline Engine  145

Engine Block Heater  148

Fuel and Refueling

Safety Precautions  150

Fuel Quality  151

Fuel Filler Funnel Location  151

Running Out of Fuel  151

Refueling  152

Fuel Consumption  155

Emission Control System  156

Transmission

Automatic Transmission  159

Four-Wheel Drive

Using Four-Wheel Drive  165

Rear Axle

Limited Slip Differential  172

Brakes

General Information  173

Hints on Driving With Anti-Lock

Brakes  173

Parking Brake  174

Hill Start Assist  174

Stability Control

Principle of Operation  177

Using Stability Control  178

Terrain Control

Using Hill Descent Control  180

Parking Aids

Principle of Operation  182

Rear Parking Aid  182

Front Parking Aid  183

Rear View Camera  184

Cruise Control

Principle of Operation  187

Using Cruise Control  187

Driving Aids

Blind Spot Information System  189

Steering  193

Drive Control  194

Self-Leveling Suspension  194

Load Carrying

Rear Under Floor Storage  196

Roof Racks and Load Carriers  197

Load Limit  198

Towing

Towing a Trailer  203

Trailer Sway Control  204

Recommended Towing Weights  204

Essential Towing Checks  207

Towing Points  214

Towing the Vehicle on Four Wheels  215

Traction Control

Driving Hints

Principle of Operation……………………………

176

Breaking-In………………………………………………

218

Using Traction Control

176

Reduced Engine Performance……………..

218

3

image21image22

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image23image24

Table of Contents

image25

Economical Driving  218

Driving Through Water  219

Floor Mats  219

Roadside Emergencies

Roadside Assistance  221

Hazard Warning Flashers  222

Fuel Shutoff  222

Jump Starting the Vehicle  223

Customer Assistance

Getting the Services You Need  226

In California (U.S. Only)  227

The Better Business Bureau (BBB) Auto

Line Program (U.S. Only)  228

Utilizing the Mediation/Arbitration

Program (Canada Only)  229

Getting Assistance Outside the U.S. and

Canada  229

Ordering Additional Owner’s

Literature  230

Reporting Safety Defects (U.S.

Only)  231

Reporting Safety Defects (Canada

Only)  231

Fuses

Fuse Specification Chart  233

Changing a Fuse  241

Maintenance

General Information  243

Opening and Closing the Hood  243

Under Hood Overview  244

Engine Oil Dipstick  245

Engine Oil Check  245

Oil Change Indicator Reset  246

Engine Coolant Check  247

Automatic Transmission Fluid

Check  251

Transfer Case Fluid Check  251

image26

4

Brake Fluid Check  252

Washer Fluid Check  252

Fuel Filter  253

Changing the 12V Battery  253

Checking the Wiper Blades  255

Changing the Wiper Blades  255

Adjusting the Headlamps  256

Removing a Headlamp  257

Changing a Bulb  257

Bulb Specification Chart  260

Changing the Engine Air Filter  262

Vehicle Care

General Information  264

Cleaning Products  264

Cleaning the Exterior  264

Waxing  265

Cleaning the Engine  266

Cleaning the Windows and Wiper

Blades  266

Cleaning the Interior  267

Cleaning the Instrument Panel and

Instrument Cluster Lens  267

Cleaning Leather Seats  268

Repairing Minor Paint Damage  269

Cleaning the Wheels  269

Vehicle Storage  270

Wheels and Tires

General Information  272

Tire Care  275

Using Snow Chains  290

Tire Pressure Monitoring System  291

Changing a Road Wheel  296

Technical Specifications  301

Capacities and Specific-

ations

Engine Specifications  303

Motorcraft Parts  303

image27

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image28image29

Table of Contents

image30

Vehicle Identification Number……………

305

Ford Protect

Vehicle Certification Label………………….

306

Ford Protect…………………………………………..

436

Transmission Code Designation………..

306

Scheduled Maintenance

Capacities and Specifications…………….

307

Audio System

General Maintenance Information…….

438

Normal Scheduled Maintenance………..

441

General Information………………………………

312

Special Operating Conditions Scheduled

Audio Unit – Vehicles With: Sony AM/FM/

Maintenance………………………………………

444

CD………………………………………………………….

313

Scheduled Maintenance Record………..

447

Audio Unit – Vehicles With: AM/FM/CD/

Appendices

SYNC/Satellite Radio………………………..

316

Digital Radio……………………………………………

318

End User License Agreement………………

457

Satellite Radio……………………………………….

320

USB Port………………………………………………….

323

Media Hub………………………………………………

323

SYNC™

General Information……………………………..

324

Using Voice Recognition………………………

326

Using SYNC™ With Your Phone…………

328

SYNC™ Applications and Services……

339

Using SYNC…………………………………………………..™WithYourMedia

342

Player

SYNC™ Troubleshooting…………………….

350

SYNC™ 3

General Information……………………………..

359

Home Screen………………………………………….

372

Using Voice Recognition……………………….

373

Entertainment……………………………………….

380

Climate……………………………………………………

390

Phone………………………………………………………

393

Navigation………………………………………………

398

Apps………………………………………………………..

406

Settings………………………………………………….

409

SYNC™ 3 Troubleshooting…………………..

421

Accessories

Accessories…………………………………………….

434

5

image31image32

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image33image34

6

image35image36

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image37image38

Introduction

image39

ABOUT THIS MANUAL

Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about your vehicle, the greater the safety and pleasure you will get from driving it.

WARNING

image40

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that

image41

you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

image42

Note: This manual describes product features and options available throughout the range of available models, sometimes even before they are generally available. It may describe options not fitted to the vehicle you have purchased.

Note: Some of the illustrations in this manual may show features as used in different models, so may appear different to you on your vehicle.

Note: Always use and operate your vehicle in line with all applicable laws and regulations.

Note: Pass on this manual when selling your vehicle. It is an integral part of your vehicle.

This manual may qualify the location of a component as left-hand side or right-hand side. The side is determined when facing forward in the seat.

7

image43

E154903

image44

ARight-hand side. B Left-hand side.

SYMBOLS GLOSSARY

These are some of the symbols you may see on your vehicle.

Air conditioning system

image45

E162384

Air conditioning system lubricant

image46

E231157  type

image47

Anti-lock braking system

Avoid smoking, flames or sparks

image48

Battery

image49

Battery acid

image50

Brake fluid – non petroleum based

image51

Brake system

image52image53

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image54image55

Introduction

image56

Cabin air filter image57image58 Front airbag

image59image60

Check fuel cap

image61

Child safety door lock or unlock

image62

Child seat lower anchor

image63

Child seat tether anchor

image64

Cruise control

image65

E71340

Do not open when hot

image66

Engine air filter

image67

Engine coolant

image68

Engine coolant temperature

image69

E67017

Front fog lamps

image70

Fuel pump reset

image71

Fuse compartment

image72

Hazard warning flashers

image73

Heated rear window

image74

Heated windshield

image75

Interior luggage compartment release

image76

Jack

image77

Keep out of reach of children

image78

E161353

Engine oil

Lighting control

Explosive gas

Low tire pressure warning

Fan warning

Maintain correct fluid level

Fasten seatbelt

Note operating instructions

E71880

Panic alarm

Flammable

E231160

8

image79image80image81image82image83image84image85image86image87image88image89

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image90image91

Introduction

image92

Parking aid

image93

E139213

Parking brake

image94

Power steering fluid

image95

Power windows front/rear

image96

Power window lockout

image97

Requires registered technician

image98

E231159

Safety alert

image99

See Owner’s Manual

image100

See Service Manual

image101

E231158

Service engine soon

image102

Side airbag

image103

Shield the eyes

image104

Stability control

image105

E138639

Windshield wash and wipe

image106image107

DATA RECORDING

Service Data Recording

Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and service your vehicle, Ford Motor Company (Ford of Canada in Canada), and service and repair facilities may access or share among them vehicle diagnostic information received through a direct connection to your vehicle when diagnosing or servicing your vehicle. Additionally, Ford Motor Company (Ford of Canada, in Canada) may, where permitted by law, use vehicle diagnostic information for vehicle improvement or with other information we may have about you, (for example, your contact information), to offer you products or services that may interest you. Data may be provided to our service providers such as part suppliers that may help diagnose malfunctions, and who are similarly obligated to protect data. We retain this data only as long as necessary to perform these functions or to comply with law. We may provide information where required in response to official requests to law enforcement or other government authorities or third parties acting with lawful authority or court order, and such information may be used in legal proceedings. For U.S. only (if equipped), if you choose to use connected apps and services, such as SYNC Vehicle Health Report or MyFord Mobile App, you consent that certain diagnostic information may also be accessed electronically by Ford Motor Company and Ford authorized service facilities, and that the diagnostic information may be used to provide

9

image108

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image109image110

Introduction

image111

services to you, personalizing your experience, troubleshoot, and to improve products and services and offer you products and services that may interest you, where permitted by law. For Canada only, for more information, please review the Ford of Canada privacy policy at www.ford.ca, including our U.S. data storage and use of service providers in other jurisdictions who may be subject to legal requirements in Canada, the United States and other countries applicable to them, for example, lawful requirements to disclose personal information to governmental authorities in those countries. See SYNC™ (page 324).

Event Data Recording

This vehicle is equipped with an event data recorder. The main purpose of an event data recorder is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle; this data will assist in understanding how a vehicle’s systems performed. The event data recorder is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.

The event data recorder in this vehicle is designed to record such data as:

How various systems in your vehicle were operating;
Whether or not the driver and passenger safety belts were buckled/fastened;
How far (if at all) the driver was depressing the accelerator and/or the brake pedal; and
How fast the vehicle was traveling; and
Where the driver was positioning the steering wheel.

10

image112

This data can help provide a better understanding of the circumstances in which crashes and injuries occur.

Note: Event data recorder data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the event data recorder under normal driving conditions and no personal data or information (e.g., name, gender, age, and crash location) is recorded (see limitations regarding 911 Assist and Traffic, directions and Information privacy below). However, parties, such as law enforcement, could combine the event data recorder data with the type of personally identifying data routinely acquired during a crash investigation.

To read data recorded by an event data recorder, special equipment is required, and access to the vehicle or the event data recorder is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have such special equipment, can read the information if they have access to the vehicle or the event data recorder. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.

image113

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image114image115

Introduction

image116

Note: Including to the extent that any law pertaining to Event Data Recorders applies to SYNC or its features, please note the following: Once 911 Assist (if equipped) is enabled (set ON), 911 Assist may, through any paired and connected cell phone, disclose to emergency services that the vehicle has been in a crash involving the deployment of an airbag or, in certain vehicles, the activation of the fuel pump shut-off. Certain versions or updates to 911 Assist may also be capable of being used to electronically or verbally provide to 911 operators the vehicle location (such as latitude and longitude), and/or other details about the vehicle or crash or personal information about the occupants to assist 911 operators to provide the most appropriate emergency services. If you do not want to disclose this information, do not activate the 911 Assist feature. See SYNC™ (page 324).

Additionally, when you connect to Traffic, Directions and Information (if equipped, U.S. only), the service uses GPS technology and advanced vehicle sensors to collect the vehicle’s current location, travel direction, and speed (“vehicle travel information”), only to help provide you with the directions, traffic reports, or business searches that you request. If you do not want Ford or its vendors to receive this information, do not activate the service. For more information, see Traffic, Directions and Information, Terms and Conditions. See SYNC™ (page 324).

CALIFORNIAPROPOSITION65

WARNINGS

image117

Some constituents of engine exhaust, certain vehicle components, certain fluids contained in vehicles

image118

and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the

image119

State of California to cause cancer and reproductive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash your hands after handling.

image120

PERCHLORATE

Certain components in your vehicle such as airbag modules, seatbelt pretensioners and remote control batteries may contain perchlorate material. Special handling may apply for service or vehicle end of life disposal.

For more information visit:

image121

Web Address

www.dtsc.ca.gov/hazard-

ouswaste/perchlorate

FORD CREDIT

US Only

Ford Credit offers a full range of financing and lease plans to help you acquire your vehicle. If you have financed or leased your vehicle through Ford Credit, thank you for your business.

11

image122image123

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image124image125

Introduction

image126

We offer a number of convenient ways for you to contact us, and to manage your account.

Call 1-800-727-7000.

For more information about Ford Credit and access to the Account Manager, go to www.fordcredit.com.

REPLACEMENT PARTS RECOMMENDATION

We have built your vehicle to the highest standards using quality parts. We recommend that you demand the use of genuine Ford and Motorcraft parts whenever your vehicle requires scheduled maintenance or repair. You can clearly identify genuine Ford and Motorcraft parts by looking for the Ford, FoMoCo or Motorcraft branding on the parts or their packaging.

Scheduled Maintenance and Mechanical Repairs

One of the best ways for you to make sure that your vehicle provides years of service is to have it maintained in line with our recommendations using parts that conform to the specifications detailed in this Owner’s Manual. Genuine Ford and Motorcraft parts meet or exceed these specifications.

Collision Repairs

We hope that you never experience a collision, but accidents do happen. Genuine Ford replacement collision parts meet our stringent requirements for fit, finish, structural integrity, corrosion protection and dent resistance. During

12

image127

vehicle development we validate that these parts deliver the intended level of protection as a whole system. A great way to know for sure you are getting this level of protection is to use genuine Ford replacement collision parts.

Warranty on Replacement Parts

Genuine Ford and Motorcraft replacement parts are the only replacement parts that benefit from a Ford Warranty. The Ford Warranty may not cover damage caused to your vehicle as a result of failed non-Ford parts. For additional information, refer to the terms and conditions of the Ford Warranty.

SPECIAL NOTICES

New Vehicle Limited Warranty

For a detailed description of what is covered and what is not covered by your vehicle’s New Vehicle Limited Warranty, see the Warranty Manual that is provided to you along with your Owner’s Manual.

Special Instructions

For your added safety, your vehicle is fitted with sophisticated electronic controls.

WARNINGS

image128

You risk death or serious injury to yourself and others if you do not follow the instruction highlighted by

image129

the warning symbol. Failure to follow the specific warnings and instructions could result in personal injury.

Never place front seat mounted rear-facing child or infant seats in front of an active passenger airbag.

image130image131image132

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image133image134

Introduction

image135

On Board Diagnostics Data Link Connector

WARNING

image136

Do not connect wireless plug-in devices to the data link connector. Unauthorized third parties could gain

image137

access to vehicle data and impair the performance of safety related systems. Only allow repair facilities that follow our service and repair instructions to connect their equipment to the data link connector.

image138

Your vehicle has an OBD Data Link Connector (DLC) that is used in conjunction with a diagnostic scan tool for vehicle diagnostics, repairs and reprogramming services. Installing an aftermarket device that uses the DLC during normal driving for purposes such as remote insurance company monitoring, transmission of vehicle data to other devices or entities, or altering the performance of the vehicle, may cause interference with or even damage to vehicle systems. We do not recommend or endorse the use of aftermarket plug-in devices unless approved by Ford. The vehicle Warranty will not cover damage caused by an aftermarket plug-in device.

MOBILE COMMUNICATIONS EQUIPMENT

WARNING

image139

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that

image140

you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

image141

Using mobile communications equipment is becoming increasingly important in the conduct of business and personal affairs. However, you must not compromise your own or others’ safety when using such equipment. Mobile communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits. Mobile communication equipment includes, but is not limited to, cellular phones, pagers, portable email devices, text messaging devices and portable two-way radios.

EXPORT UNIQUE OPTIONS

For your particular global region, your

vehicle may be equipped with features and

options that are different from the features

and options that are described in this

Owner’s Manual. A market unique

supplement may be supplied that

complements this book. By referring to the

market unique supplement, if provided,

you can properly identify those features,

13

image142image143

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image144image145

Introduction

image146

recommendations and specifications that are unique to your vehicle. This Owner’s Manual is written primarily for the U.S. and Canadian Markets. Features or equipment listed as standard may be different on units built for export. Refer to this Owner’s Manual for all other required

information and warnings.

14

image147image148

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image149image150

Environment

image151

PROTECTING THE

ENVIRONMENT

You must play your part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps toward this aim.

15

image152image153

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image154image155

Child Safety

image156

GENERAL INFORMATION

See the following sections for directions on how to properly use safety restraints for children.

WARNINGS

image157

Always make sure your child is secured properly in a device that is appropriate for their height, age and

image158

weight. Child safety restraints must be bought separately from your vehicle. Failure to follow these instructions and guidelines may result in an increased risk of serious injury or death to your child.

All children are shaped differently. The National Highway Traffic Safety Administration and other safety

image159

organizations, base their recommendations for child restraints on probable child height, age and weight thresholds, or on the minimum requirements of the law. We recommend that you check with a NHTSA Certified Child Passenger Safety

16

image160

WARNINGS

image161

Technician (CPST) to make sure that you properly install the child restraint in your vehicle and that you consult your pediatrician to make sure you have a child restraint appropriate for your child. To locate a child restraint fitting station and CPST, contact NHTSA toll free at 1-888-327-4236 or go to www.nhtsa.dot.gov. In Canada, contact Transport Canada toll free at

1-800-333-0371 or go to www.tc.gc.ca to find a Child Car Seat Clinic in your area. Failure to properly restrain children in child restraints made especially for their height, age and weight, may result in an increased risk of serious injury or death to your child.

On hot days, the temperature inside the vehicle can rise very quickly. Exposure of people or animals to

image162

these high temperatures for even a short time can cause death or serious heat related injuries, including brain damage. Small children are particularly at risk.

image163image164

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image165image166

Child Safety

image167

Recommendations for Safety Restraints for Children

image168

Recommended restraint

Child  Child size, height, weight, or age

type

Infants or

toddlers

Small children

Children weighing 40 lb (18 kg) or less

Use a child safety seat

(sometimes called an

(generally age four or younger).

infant carrier, convertible

seat, or toddler seat).

Children who have outgrown or no longer

properly fit in a child safety seat (gener-

ally children who are less than 4 ft. 9 in.

Use a belt-positioning

(1.45 m) tall, are greater than age four

and less than age 12, and between 40 lb

booster seat.

(18 kg) and 80 lb (36 kg) and upward to

100 lb (45 kg) if recommended by your

child restraint manufacturer).

Children who have outgrown or no longer

Use a vehicle seatbelt

properly fit in a belt-positioning booster

having the lap belt snug

Larger children

seat (generally children who are at least

and low across the hips,

4 ft. 9 in. (1.45 m) tall or greater than

shoulder belt centered

80 lb (36 kg) or 100 lb (45 kg) if recom-

across the shoulder and

mended by child restraint manufacturer).

chest, and seatback

upright.

You are required by law to properly use safety seats for infants and toddlers in the United States and Canada.
Many states and provinces require that small children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 lb (36 kg). Check your local and state or provincial laws for specific requirements about the safety of children in your vehicle.
When possible, always properly restrain children 12 years of age and under in a rear seating position of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in a front seating position.

INSTALLING CHILD RESTRAINTS

Child Seats

image169

E142594

17

image170image171

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image172image173

Child Safety

image174

Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers, or children weighing 40 pounds (18 kilograms) or less (generally age four or younger).

Using Lap and Shoulder Belts

WARNINGS

image175

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag.

image176

If you must use a forward-facing child seat in the front seat, move the vehicle seat upon which the seat is installed all the way back.

Airbags can kill or injure a child in a child seat. Children 12 and under should be properly restrained in the

image177

rear seat whenever possible.

Depending on where you secure a child restraint, and depending on the child restraint design, you may block

image178

access to certain seatbelt buckle assemblies and LATCH lower anchors, rendering those features potentially unusable. To avoid risk of injury, occupants should only use seating positions where they are able to be properly restrained.

image179

When installing a child safety seat with combination lap and shoulder belts:

Use the correct seatbelt buckle for that seating position.
Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling.

18

image180

Place the vehicle seat upon which the child seat will be installed in the upright position.
Put the seatbelt in the automatic locking mode. This vehicle does not require the use of a locking clip.

Perform the following steps when installing the child seat with combination lap and shoulder belts:

Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat.

image181

E142528

1.Position the child safety seat in a seat with a combination lap and shoulder belt.

image182

E142529

2.Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together.

image183

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image184image185

Child Safety

image186image187

E142530

3.While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted.

image188

E206121

4.Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it.

E142875

5.To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out.

Note: The automatic locking mode is available on the front passenger and rear seats. This vehicle does not require the use of a locking clip.

6.Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode.
7.Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode (you should not be able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat Steps 5 and 6.

image189

E142533

19

image190image191

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image192image193

Child Safety

image194

8.Remove remaining slack from the belt. Force the seat down with extra weight, for example, by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that will exist once the extra weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle. Sometimes, a slight lean toward the buckle will help to remove remaining slack from the belt.
9.Attach the tether strap (if the child seat is equipped).

image195

E142534

10.Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place.

To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 in (2.5 cm) of movement for proper installation.

We recommend checking with a NHTSA Certified Child Passenger Safety Technician to make certain the child restraint is properly installed. In Canada, check with Transport Canada for referral to a Child Car Seat Clinic.

Using Lower Anchors and Tethers for CHildren (LATCH)

WARNING

image196

Never attach two child safety seats to the same anchor. In a crash, one anchor may not be strong enough to

image197

hold two child safety seat attachments and may break, causing serious injury or death.

image198

The LATCH system is composed of three vehicle anchor points: two lower anchors located where the vehicle seatback and seat cushion meet (called the seat bight) and one top tether anchor located behind that seating position.

LATCH compatible child safety seats have two rigid or webbing mounted attachments that connect to the two lower anchors at the LATCH equipped seating positions in your vehicle. This type of attachment method eliminates the need to use seatbelts to attach the child seat, however the seatbelt can still be used to attach the child seat if the lower anchors are not used. For forward-facing child seats, the top tether strap must also be attached to the proper top tether anchor, if a top tether strap has been provided with your child seat. We recommend the use of a child safety seat having a top tether strap. See Using Tether Straps in this chapter.

Your vehicle has LATCH lower anchors for child seat installation at the seating positions marked with the child seat symbol.

20

image199image200

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image201image202

Child Safety

image203

The locator symbols are on round plastic

buttons for the center seat and on

rectangular tags for the outboard seats.

image204

Follow the instructions on attaching child

safety seats with tether straps. See Using

Tether Straps in this chapter.

Attach LATCH lower attachments of the

child seat only to the anchors shown.

Each time you use the safety seat, check

that the seat is properly attached to the

lower anchors and tether anchor, if

E205021

applicable. Tug the child seat from side to

side and forward and back where it is

secured to the vehicle. The seat should

move less than one inch when you do this

image205

for a proper installation.

If the safety seat is not anchored properly,

the risk of a child being injured in a crash

greatly increases.

Combining Seatbelt and LATCH

Lower Anchors for Attaching Child

Safety Seats

E206122

The LATCH anchors are at the rear section of the rear seat between the cushion and seatback, below the locator symbols on the seatback. Follow the child seat manufacturer ’s instructions to properly install a child seat with LATCH attachments.

image206

E144054

21

image207

When used in combination, either the seatbelt or the LATCH lower anchors may be attached first, provided a proper installation is achieved. Attach the tether strap afterward, if included with the child seat.

Using Tether Straps

Many forward-facing child safety seats include a tether strap which extends from the back of the child safety seat and hooks to an anchoring point called the top tether anchor. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap, or to obtain a longer tether strap if the tether strap on your safety seat does not reach the appropriate top tether anchor in the vehicle.

image208

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image209image210

Child Safety

image211

Some of the rear seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as described below.

In the third row center seating position, the tether anchor is a loop at the bottom of the seatback.

The tether strap anchors in your vehicle are in the following positions (shown from top view).

Second row bench seat

image212

Once the child safety seat has been installed using either the seatbelt, the lower anchors of the LATCH system, or both, you can attach the top tether strap.

If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat. Keeping the child seat just touching the vehicle seat gives the best protection in a severe crash.

Perform the following steps to install a child safety seat with tether anchors:

Second row outboard seating positions

image213

E205023

Second row bucket seats

image214

E205024

Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor.

image215

E205025

Second row center seating position (if equipped)

image216

E205026

22

image217

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image218image219

Child Safety

image220

1.For center seating positions, route the child safety seat tether strap over the

image221

back of the seat. For outboard seating positions, route the tether strap under the head restraint and between the head restraint posts. If the top of the safety seat hits the head restraint, recline the seat back slightly to obtain proper fit.

2.  Locate the correct anchor for the selected seating position.

E205029

image222

5. Rotate the tether strap clip.

6.  Tighten the child safety seat tether strap according to the manufacturer’s instructions.

Third row center seating position

1.  Route the child safety seat tether strap over the back of the seat.

image223

E205027

3.Grasp the tether strap and position it to the seat frame.

image224

E205028

4.Rotate the tether strap, and clip the tether strap to the anchor on the seat frame.

image225

E205030

2.Locate the anchor webbing loop for the seating position. You may need to pull back the top of the hinged panel along the bottom of the seatback to access the tether anchor.

23

image226

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image227image228

Child Safety

image229

E205032

image230

3.Clip the tether strap through the anchor loop as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a crash.

image231

E205033

4.Tighten the child safety seat tether strap according to the manufacturer’s instructions. If the safety seat is not anchored properly, the risk of a child being injured in a crash greatly increases.

If your child restraint system is equipped with a tether strap, and the child restraint manufacturer recommends its use, we also recommend its use.

BOOSTER SEATS

WARNING

image232

Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it

image233

reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.

image234

Note: Some booster seat safety belt guides may not accommodate the shoulder portion of the inflatable safety belt.

Use a belt-positioning booster seat for children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 feet 9 inches (1.45 meters) tall, are greater than age four

(4)and less than age twelve (12), and between 40 pounds (18 kilograms) and 80 pounds (36 kilograms) and upward to 100 pounds (45 kilograms) if recommended by your child restraint manufacturer). Many state and provincial laws require that children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 pounds (36 kilograms).

Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat:

image235

E142595

24

image236image237

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image238image239

Child Safety

image240

  Can the child sit all the way back against their vehicle seat back with knees bent comfortably at the edge of the seat cushion?

image241

  Can the child sit without slouching?

  Does the lap belt rest low across the hips?

  Is the shoulder belt centered on the shoulder and chest?

  Can the child stay seated like this for

the whole trip?

E70710

Always use booster seats in conjunction with your vehicle lap and shoulder belt.

Types of Booster Seats

image242

E68924

Backless booster seats

If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’s head (as measured at the tops of the ears) above the top of the seat. In this case, move the backless booster to another seating position with a higher seat back or head restraint and lap and shoulder belts, or consider using a high back booster seat.

25

image243

High back booster seats

If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice.

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The following drawings compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder. The drawings also show how the lap belt should be low and snug across the child’s hips.

image244

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image245image246

Child Safety

image247image248

E142596

image249

E142597

If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition. Do not introduce any item thicker than this under the booster seat. Check with the booster seat manufacturer’s instructions.

CHILD RESTRAINT POSITIONING

WARNINGS

image250

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag.

image251

If you must use a forward-facing child seat in the front seat, move the vehicle seat upon which the child seat is installed all

26

image252

WARNINGS

image253

the way back. When possible, all children age 12 and under should be properly restrained in a rear seating position. If all children cannot be seated and restrained properly in a rear seating position, properly restrain the largest child in the front seat.

Always carefully follow the instructions and warnings provided by the manufacturer of any child

image254

restraint to determine if the restraint device is appropriate for your child’s size, height, weight, or age. Follow the child restraint manufacturer’s instructions and warnings provided for installation and use in conjunction with the instructions and warnings provided by your vehicle

image255

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image256image257

Child Safety

image258

WARNINGS  WARNINGS

image259

manufacturer. A safety seat that is improperly installed or utilized, is inappropriate for your child’s height, age, or weight or does not properly fit the child may increase the risk of serious injury or death.

Never let a passenger hold a child on his or her lap while your vehicle is moving. The passenger cannot

image260

protect the child from injury in a crash, which may result in serious injury or death.

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood

image261

of injury or death in a crash.

Always restrain an unoccupied child seat or booster seat. These objects may become projectiles in a crash or

image262

sudden stop, which may increase the risk of serious injury.

Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it

image263

reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.

To avoid risk of injury, do not leave children or pets unattended in your vehicle.

image264image265

Recommendations for attaching child safety restraints for children

image266

Use any attachment method as indicated below by X

Combined

LATCH

LATCH

Safety belt

Safety belt

Safety belt

(lower

(lower

and top

and LATCH

only

Restraint

weight of

anchors

anchors

tether

(lower

Type

child and

and top

only)

anchor

anchors

child seat

tether

and top

anchor)

tether

anchor)

Rear facing

Up to 65 lb

X

X

child seat

(29.5 kg)

Rear facing

Over 65 lb

X

child seat

(29.5 kg)

Forward

Up to 65 lb

X

X

X

facing

(29.5 kg)

child seat

Forward

Over 65 lb

X

X

facing

(29.5 kg)

child seat

Note: The child seat must rest tightly

CHILD SAFETY LOCKS

against the vehicle seat upon which it is

installed. It may be necessary to lift or

remove the head restraint. See Seats (page

When these locks are set, the rear doors

121).

cannot be opened from the inside.

27

image267image268

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image269image270

Child Safety

image271image272

E205034

The locks are located on the rear edge of each rear door and must be set separately for each door.

Move the lock control up to engage the lock. Move it down to disengage the lock.

28

image273image274

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image275image276

Seatbelts

image277

PRINCIPLE OF OPERATION

WARNINGS

image278

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

image279

To reduce the risk of injury, make sure children sit where they can be properly restrained.

image280

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot

image281

protect the child from injury in a crash, which may result in serious injury or death.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even

image282

when an airbag supplemental restraint system is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in

image283

these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety

image284

belt.

WARNINGS

image285

When possible, all children 12 years old and under should be properly restrained in a rear seating position.

image286

Failure to follow this could seriously increase the risk of injury or death.

Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn

image287

a small child. Check seat covers and buckles before you place a child anywhere near them.

Front and rear seat occupants, including pregnant women, should wear safety belts for optimum

image288

protection in an accident.

image289

All seating positions in this vehicle have lap and shoulder safety belts. All occupants of the vehicle should always properly wear their safety belts, even when an airbag supplemental restraint system is provided.

The safety belt system consists of:

Lap and shoulder safety belts.
Shoulder safety belt with automatic locking mode, (except driver safety belt).
Height adjuster at the front outboard seating positions.
Safety belt pretensioner at the front outboard seating positions.

image290

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and

image291

one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

29

image292

E71880

Safety belt warning light and chime.

image293

E67017

Crash sensors and monitoring system with readiness indicator.

image294

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image295image296

Seatbelts

image297

The safety belt pretensioners at the front seating positions are designed to tighten the safety belts when activated. In frontal and near-frontal crashes, the safety belt pretensioners may be activated alone or, if the crash is of sufficient severity, together with the front airbags. In side crashes and rollovers, the pretensioners will be activated when the Safety Canopy is activated.

FASTENING THE SEATBELTS

The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts.

image298

E142587

1.Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

E142588

image299

2.To unfasten, press the release button and remove the tongue from the buckle.

Using Seatbelts During Pregnancy

WARNING

image300

Always ride and drive with your seatback upright and the seatbelt properly fastened. The lap portion of

image301

the seatbelt should fit snug and be positioned low across the hips. The shoulder portion of the seatbelt should be positioned across the chest. Pregnant women should also follow this practice. See the following figure.

image302

E142590

30

image303image304

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image305image306

Seatbelts

image307

Pregnant women should always wear their seatbelt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow. The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest.

Seatbelt Locking Modes

WARNINGS

image308

After any vehicle crash, the seatbelt system at all passenger seating positions must be checked by an

image309

authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly. In addition, all seatbelts should be checked for proper function.

The belt and retractor assembly must be replaced if the seatbelt assembly automatic locking retractor

image310

feature or any other seatbelt function is not operating properly when checked by an authorized dealer. Failure to replace the belt and retractor assembly could increase the risk of injury in crashes.

image311

All safety restraints in the vehicle are combination lap and shoulder belts. The driver seatbelt has the first type of locking mode. The front outboard passenger and rear seat seatbelts have both types of locking modes described as follows:

In addition, the retractor is designed to lock if the webbing is pulled out too quickly. If this occurs, let the belt retract slightly and pull webbing out again in a slow and controlled manner.

Automatic Locking Mode

In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver seatbelt.

When to Use the Automatic Locking Mode

This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in a rear seating position whenever possible. See Child Safety (page 16).

How to Use the Automatic Locking Mode

image312

Vehicle Sensitive Mode

This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of about 5 mph

(8 km/h) or more, the combination seatbelts will lock to help reduce forward movement of the driver and passengers.

image313

E142591

1.Buckle the combination lap and shoulder belt.
2.Grasp the shoulder portion and pull downward until the entire belt is pulled out.

31

image314

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image315image316

Seatbelts

image317

Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the seatbelt is now in the automatic locking mode.

How to Disengage the Automatic Locking Mode

Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

2.Release the buttons and pull down on the height adjuster to make sure it is locked in place.

Second Row Comfort Guide

WARNING

image318

Position the safety belt comfort guide so that the belt rests across the middle of your shoulder. Failure

image319

to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a crash.

SEATBELT HEIGHT ADJUSTMENT

image320image321

WARNING

image322

Position the safety belt height adjuster so that the belt rests across the middle of your shoulder. Failure

image323

to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a crash.

image324

E205036

image325

The second row outboard lap and shoulder belt is equipped with a belt comfort guide. This guide is attached to the quarter trim panel. Use it to adjust the comfort of the shoulder belt for smaller occupants in the outboard second row seats.

image326

E205035

Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.

To adjust the shoulder belt height:

1.  Press the side release buttons and slide

the height adjuster up or down.

E205037

32

image327image328

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image329image330

Seatbelts

image331

To adjust the comfort guide:

1.Slip the shoulder belt into the belt guide (the portion of the belt between the latch tongue and the D-ring, not the portion where the belt exits from the quarter trim panel).
2.Slide the guide up or down along the webbing so that the belt is centered on the occupant’s shoulder.

SEATBELT WARNING LAMP AND INDICATOR CHIME

This lamp illuminates and an

audible warning will sound if the

E71880

driver’s safety belt has not been

image332

fastened when the vehicle’s ignition is turned on.

Conditions of operation

image333

If…

Then…

The driver’s safety belt is not buckled

The safety belt warning light illuminates 1-

before the ignition switch is turned to the

2 minutes and the warning chime sounds

on position…

4-8 seconds.

The driver’s safety belt is buckled while the

The safety belt warning light and warning

indicator light is illuminated and the

chime turn off.

warning chime is sounding…

The driver’s safety belt is buckled before

The safety belt warning light and indicator

the ignition switch is turned to the on posi-

chime remain off.

tion…

SEATBELT REMINDER

Belt-Minder™

This feature supplements the safety belt

warning function by providing additional

reminders that intermittently sound a tone

and illuminate the safety belt warning light

when you are in the driver seat and a safety

belt is unbuckled.

33

image334image335

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image336image337

Seatbelts

image338image339

If…

Then…

You buckle your safety belt before you

The Belt-Minder feature will not activate.

switch the ignition on or less than 1-2

minutes elapse after you switch the ignition

on…

You do not buckle your safety belt before

The Belt-Minder feature activates, the

your vehicle reaches at least 6 mph (9.7

safety belt warning light illuminates and a

km/h) and 1-2 minutes elapse after you

warning tone sounds for 6 seconds every

switch the ignition on…

25 seconds, repeating for about 5 minutes

or until you buckle your safety belt.

The driver safety belt is unbuckled for about 1 minute while the vehicle is traveling at least 6 mph (9.7 km/h) and more than 1-2 minutes elapse after you switch the ignition on…

Deactivating and Activating the Belt-Minder Feature

WARNING

image340

While the system allows you to deactivate it, this system is designed to improve your chances of being

image341

safely belted and surviving an accident. We recommend you leave the system activated for yourself and others who may use the vehicle.

image342

Read Steps 1 – 4 thoroughly before proceeding with the programming procedure.

Before following the procedure, make sure that:

The parking brake is set.
The transmission is in park (P).
The ignition is off.
All vehicle doors are closed.
The driver safety belt is unbuckled.
1.Switch the ignition on. Do not start the engine.

The Belt-Minder feature activates, the safety belt warning light illuminates and a warning tone sounds for 6 seconds every 25 seconds, repeating for about 5 minutes or until you buckle your safety belt.

2.Wait until the safety belt warning light turns off (about one minute). After Step 2, wait an additional 5 seconds before proceeding with Step 3. Once you start Step 3, you must complete the procedure within 60 seconds.
3.Buckle then unbuckle the safety belt three times at a moderate speed, ending in the unbuckled state. After Step 3, the safety belt warning light turns on.
4.While the safety belt warning light is on, buckle then unbuckle the safety belt. After Step 4, the safety belt warning light flashes for confirmation.
This will switch the feature off if it is currently on.
This will switch the feature on if it is currently off.

34

image343image344

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image345image346

Seatbelts

image347

CHILD RESTRAINT AND SEATBELT MAINTENANCE

Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged. Inspect the vehicle and child seat safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All vehicle safety belt assemblies, including retractors, buckles, front safety belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seat back (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a crash. Read the child restraint manufacturer’s instructions for additional inspection and maintenance information specific to the child restraint.

Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced. However, if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a crash should also be inspected and replaced if either damage or improper operation is noted.

Properly care for safety belts. See Vehicle Care (page 264).

WARNINGS

image348

Only use extensions provided free of charge by Ford Motor Company dealers. The dealer will provide an

image349

extension designed specifically for this vehicle, model year and seating position. The use of an extension intended for another vehicle, model year or seating position may not offer you the full protection of your vehicle’s seatbelt restraint system.

Never use seatbelt extensions to install child restraints.

image350

Do not use a seatbelt extension with an inflatable seatbelt.

image351

Do not use extensions to change the fit of the belt across the torso, over the lap or to make the seatbelt

image352

buckle easier to reach.

image353

If, because of body size or driving position, it is not possible to properly fasten the seatbelt over your lap and shoulder, an extension that is compatible with the seatbelts is available free of charge from Ford Motor Company dealers. Only Ford seatbelt extensions made by the original equipment seatbelts manufacturer should be used with Ford seatbelts. Ask your authorized dealer if your extension is compatible with your Ford vehicle restraint system.

SEATBELT EXTENSION

WARNINGS

image354

Persons who fit into the vehicle’s

image355

seatbelt should not use an extension.

Unnecessary use could result in

serious personal injury in the event of a

crash.

35

image356image357

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image358image359

Supplementary Restraints System

image360

PRINCIPLE OF OPERATION

WARNINGS

image361

Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close

image362

to the trim covering the airbag module.

All occupants of your vehicle, including the driver, should always properly wear their safety belts, even

image363

when an airbag supplemental restraint system is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.

Always transport children 12 years old and under in the back seat and always properly use appropriate

image364

child restraints. Failure to follow this could seriously increase the risk of injury or death.

Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or

image365

other injuries.

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag.

image366

If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses as you

image367

could be seriously injured or killed. Contact your authorized dealer as soon as possible.

Several airbag system components get hot after inflation. To avoid risk of injury, do not touch them after

image368

inflation.

If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag

image369

is not replaced, the unrepaired area will increase the risk of injury in a crash.

image370

36

image371

The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag.

Note: You will hear a loud bang and see a cloud of harmless powdery residue if an airbag deploys. This is normal.

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (for example, baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.

While the system is designed to help reduce serious injuries, contact with a deploying airbag may also cause abrasions or swelling. Temporary hearing loss is also a possibility as a result of the noise associated with a deploying airbag. Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control.

Routine maintenance of the airbags is not required.

image372

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image373image374

Supplementary Restraints System

image375

Restraint Safety System

The restraint safety system provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.

Your vehicle restraint safety system consists of:

Driver and passenger dual-stage airbag supplemental restraints.
Front outboard safety belts with pretensioners, energy management retractors (first row only), and safety belt usage sensors.
Driver seat position sensor.
Front crash severity sensors.
Restraints control module with impact and safing sensors.
Restraint system warning light and backup tone.

module. During a crash, the restraints control module may activate the safety belt pretensioners and/or either one or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions.

DRIVER AND PASSENGER AIRBAGS

WARNINGS

image376

Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can

image377

result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag.

image378

If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

image379

The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, and indicator lights.

How does the restraint safety system work?

The restraint safety system can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the restraints control

E151127

image380

The driver and passenger front airbags will deploy during significant frontal and near frontal crashes.

The driver and passenger front airbag system consists of:

Driver and passenger airbag modules.

37

image381image382

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image383image384

Supplementary Restraints System

image385

· Crash sensors and monitoring

system with readiness indicator.

E67017

See Crash Sensors and Airbag

image386

Indicator (page 40).

Proper Driver and Front Passenger Seating Adjustment

WARNING

image387

The National Highway Traffic Safety Administration recommends a minimum distance of at least 10 in

image388

(25 cm) between an occupant’s chest and the driver airbag module.

image389

To properly position yourself away from the airbag:

Move your seat to the rear as far as you can while still reaching the pedals comfortably.
Recline the seat slightly (one or two degrees) from the upright position.

E142846

image390

Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a crash.

SIDE AIRBAGS

After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. Properly seated occupants sit upright, lean against the seat back, and center themselves on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.

WARNINGS

image391

Do not place objects or mount equipment on or near the airbag cover, on the side of the seatbacks

image392

(of the front seats), or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the

image393

side airbags and increase the risk of injury in an accident.

Children and Airbags

WARNING

image394

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag.

image395

If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

image396

38

image397

Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the

image398

seatback.

image399

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image400image401

Supplementary Restraints System

image402

WARNINGS

image403

Do not attempt to service, repair, or modify the airbag, its fuses or the seat cover on a seat containing an

image404

airbag as you could be seriously injured or killed. Contact your authorized dealer as soon as possible.

If the side airbag has deployed, the airbag will not function again. The side airbag system (including the

image405

seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

·Crash sensors and monitoring

system with readiness indicator.

E67017

See Crash Sensors and Airbag

image406

Indicator (page 40).

The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags.

The side airbags are located on the outboard side of the seatbacks of the front seats. In certain sideways crashes, the airbag on the side affected by the crash will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact crashes.

image407image408

E152533

SAFETY CANOPY™

WARNINGS

image409

Do not place objects or mount equipment on or near the headliner at the siderail that may come into

image410

contact with a deploying curtain airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

Do not lean your head on the door. The curtain airbag could injure you as it deploys from the headliner.

image411

Do not attempt to service, repair, or modify the curtain airbag supplemental restraint system, its

image412

fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing curtain airbags as you could be seriously injured or killed. Contact your authorized dealer as soon as possible.

The system consists of the following:

A label or embossed side panel indicating that side airbags are found on your vehicle.
Side airbags located inside the seatback of the driver and front passenger seats.

image413

All occupants of your vehicle, including the driver, should always properly wear their seatbelts, even

image414

when an airbag supplemental restraint system is provided. Failure to properly wear your seatbelt could seriously increase the risk of injury or death.

39

image415

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image416image417

Supplementary Restraints System

image418

WARNINGS

image419

To reduce risk of injury, do not obstruct or place objects in the deployment path of the airbag.

image420

If the curtain airbags have deployed, the curtain airbags will not function again. The curtain airbags (including

image421

the A, B and C pillar trim and headliner) must be inspected and serviced as soon as possible. If the curtain airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

image422

The Safety Canopy deploys during significant side crashes or when a certain likelihood of a rollover event is detected by the rollover sensor. The Safety Canopy is mounted to the roof side-rail sheet metal, behind the headliner, above each row of seats. In certain sideways crashes or rollover events, the Safety Canopy will be activated, regardless of which seats are occupied. The Safety Canopy is designed to inflate between the side window area and occupants to further enhance protection provided in side impact crashes and rollover events.

image423

The system consists of the following:

Safety Canopy curtain airbags located above the trim panels over the front and rear side windows identified by a label or wording on the headliner or roof-pillar trim.
A flexible headliner which opens above the side doors to allow air curtain deployment

· Crash sensors and monitoring

system with a readiness

E67017

indicator. See Crash Sensors

image424

and Airbag Indicator (page 40).

Properly restrain children 12 years old and under in the rear seats. The Safety Canopy will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening.

The design and development of the Safety Canopy included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy).

E75004

40

image425

CRASH SENSORS AND AIRBAG INDICATOR

WARNING

image426

Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body

image427

structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of the vehicle.

image428image429

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image430image431

Supplementary Restraints System

image432

Your vehicle has a collection of crash and occupant sensors which provide information to the restraints control module which deploys (activates) the front safety belt pretensioners, driver airbag, passenger airbag, seat mounted side airbags, and the Safety Canopy®. Based on the type of crash (frontal impact, side impact or rollover), the restraints control module will deploy the appropriate safety devices.

The restraints control module also monitors the readiness of the above safety devices plus the crash and occupant sensors. The readiness of the safety system is indicated by a warning indicator light in the instrument cluster or by a backup tone if the warning light is not working. See Instrument Cluster (page 84). Routine maintenance of the airbag is not required.

A difficulty with the system is indicated by one or more of the following:

The readiness light will not

illuminate immediately after the

E67017

ignition is turned on.

image433

The readiness light will either flash or stay lit.
A series of five beeps will be heard. The tone pattern will repeat periodically until the problem, the light or both are repaired.

If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a crash.

41

image434

The fact that the safety belt pretensioners or front airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (crash severity, belt usage) were not appropriate to activate these safety devices.

The design of the front airbags is to activate only in frontal and near-frontal crashes (not rollovers, side impacts or rear impacts) unless the crash causes sufficient frontal deceleration.
The design of the safety belt pretensioners is to activate in frontal, near-frontal and side crashes, and in rollovers.
The design of the side airbags is to inflate in certain side impact crashes. Side airbags may activate in other types of crashes if the vehicle experiences sufficient sideways motion or deformation.
The design of the Safety Canopy is to inflate in certain side impact crashes or rollover events. The Safety Canopy may activate in other types of crashes if the vehicle experiences sufficient sideways motion or deformation, or a certain likelihood of rollover.

AIRBAG DISPOSAL

Contact your authorized dealer as soon as possible. Airbags must be disposed of by qualified personnel.

image435

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image436image437

Keys and Remote Controls

image438

PRINCIPLE OF OPERATION

The remote control allows you to:

Remotely lock or unlock the vehicle doors.
Unlock the doors without actively using a key or remote control (intelligent access only).
Remotely open the power liftgate (if equipped).
Remotely start or stop the engine and user pre-set features (if equipped).
Arm and disarm the anti-theft system.
Activate the panic alarm.

GENERAL INFORMATION ON RADIO FREQUENCIES

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. The term IC before the radio certification number only signifies that Industry Canada technical specifications were met.

The typical operating range for your transmitter is approximately 33 feet (10 meters). Vehicles with the remote start feature will have a greater range. One of the following could cause a decrease in operating range:

Weather conditions.
Nearby radio towers.

42

image439

Structures around the vehicle.
Other vehicles parked next to your vehicle.

The radio frequency used by your remote control can also be used by other radio transmitters, for example amateur radios, medical equipment, wireless headphones, wireless remote controls, cell phones, battery chargers and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key.

Note: Make sure to lock your vehicle before leaving it unattended.

Note: If you are in range, the remote control will operate if you press any button unintentionally.

Intelligent Access (If Equipped)

The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met:

You press any button on the keyless entry keypad within 3 ft (1 m) proximity of an intelligent access key.
You press the luggage compartment button.
You press a button on the transmitter.

If excessive radio frequency interference is present in the area or if the transmitter battery is low, you may need to mechanically unlock your door. You can use the mechanical key blade in your intelligent access key to open the driver door in this situation. See Remote Control (page 43).

image440

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image441image442

Keys and Remote Controls

image443

REMOTE CONTROL

Integrated Keyhead Transmitter (If

Equipped)

image444

E210695

Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. You can also use the key blade to lock and unlock the glove compartment. The transmitter portion functions as the remote control.

image445

E163047

Note: Your vehicle keys came with a security label that provides important key cut information. Keep the label in a safe place for future reference.

E138616

image446

The intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to use the push button start.

image447

E142431

The intelligent access key also contains a removable key blade that you can use to unlock your vehicle. You can also use the key blade to lock and unlock the glove compartment. Slide the release on the back of the remote control to release the key blade, then pull the blade out.

image448

Intelligent Access Key (If Equipped)

Note: A three-button remote control

operates similarly.

E138618

Note: Your vehicle keys came with a

security label that provides important key

cut information. Keep the label in a safe

place for future reference.

43

image449image450

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image451image452

Keys and Remote Controls

image453

Replacing the Battery

Note: Refer to local regulations when disposing of transmitter batteries.

Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.

Note: Replacing the battery does not erase the programmed key from your vehicle. The transmitter should operate normally.

The remote control uses one coin-type three-volt lithium battery CR2032 or equivalent.

Integrated Keyhead Transmitter

image454

4.Insert a new battery with the + facing upward. Press the battery down to make sure it is fully in the housing.
5.Reinstall the battery housing cover onto the transmitter.

Intelligent Access Key

1.Remove the key blade from the transmitter.

image455

E235202

1.Twist a thin coin in the slot of the transmitter near the key ring to remove the battery cover.
2.Carefully remove the rubber gasket from the transmitter if it does not come off with the battery cover.
3.Remove the old battery.

image456

E235203

44

image457

E142432

2.Twist a thin coin under the tab hidden behind the key blade head to remove the battery cover. Do not use the key blade to remove the cover or you could damage it.

image458

E138622

3.Remove the old battery.
4.Insert a new battery with the + facing downward. Press the battery down to make sure it is fully in the housing.

image459

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image460image461

Keys and Remote Controls

image462

5.Reinstall the battery housing cover onto the transmitter and install the key blade.

Car Finder

Press the button twice within three seconds.

image463

E138623

The horn sounds and the direction indicators flash. We recommend you use this method to locate your vehicle, rather than using the panic alarm.

Note: If any door or the liftgate is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the horn will sound twice and the direction indicators will not flash.

Sounding the Panic Alarm

Press the button to sound the

image464

panic alarm. Press the button

E138624  again or switch the ignition on to

turn it off.

Note: The panic alarm only operates when the ignition is off.

Remote Start (If Equipped)

WARNING

image465

To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or in areas that are not well

image466

ventilated.

image467

Note: Do not use remote start if your fuel level is low.

The remote start button is on the transmitter.

image468

E138625

Vehicles with automatic climate control can be configured to operate when the vehicle is remote started. See Automatic Climate Control (page 115).

Many states and provinces have restrictions for the use of remote start. Check your local and state or provincial laws for specific requirements regarding remote start systems.

The remote start system does not work if any of the following occur:

The ignition is on.
The anti-theft alarm triggers.
You switch off the feature.
The hood is open.
The transmission is not in park (P).
The battery voltage is below the minimum operating voltage.
The service engine soon indicator was on the last time your vehicle was driven.

Remote Starting Your Vehicle

Note: You must press each button within three seconds of each other. If you do not follow this sequence, your vehicle does not start remotely, the direction indicators do not flash twice and the horn does not sound.

image469

E138626

This feature allows you to start your vehicle from the outside. The transmitter has an extended operating range.

The label on your transmitter details the starting procedure.

To start your vehicle remotely:

1.Press the lock button to lock all the doors.

45

image470image471

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image472image473

Keys and Remote Controls

image474

2.Press the remote start button twice. The exterior lamps flash twice.

The horn sounds if the system fails to start, unless quiet start is on. Quiet start runs the blower fan at a slower speed to reduce noise. You can switch this feature on or off in the information display. See General Information (page 91).

Note: If you remote start your vehicle with an integrated keyhead transmitter, you must switch the ignition on before driving your vehicle. If you remote start your vehicle with an intelligent access transmitter, you must press the push button ignition switch on the instrument panel once while applying the brake pedal before driving your vehicle.

The power windows do not work during remote start and the radio does not turn on automatically.

The parking lamps remain on and the vehicle runs for 5, 10 or 15 minutes, depending on the setting.

Extending the Engine Running Time

To extend the engine running time duration of your vehicle during remote start, repeat steps 1 and 2 while the engine is running.

If the duration is set to 10 minutes, the duration extends by another 10 minutes. For example, if your vehicle had been running from the first remote start for 5 minutes, your vehicle continues to run now for a total of 20 minutes. You can extend the remote start up to a maximum of 35 minutes.

Wait at least five seconds before remote starting after the engine stops running.

Turning Your Vehicle Off After Remote Starting

You may have to be closer to your vehicle to remotely switch off your vehicle after remote starting. This is due to the added noise of your running vehicle.

You can switch this feature on or off in the information display. See General Information (page 91).

Memory Feature (If Equipped)

You can use the remote control to recall memory settings for the driver seat, power mirrors, power steering column and power adjustable foot pedals. Press the unlock button on the remote control or unlock your vehicle with the intelligent access key to recall the memory positions. You can program the remote control or intelligent access key to recall memory positions. See Memory Function (page 125).

REPLACING A LOST KEY OR REMOTE CONTROL

Replacement keys or remote controls can be purchased from an authorized dealer. Authorized dealers can program remote controls for your vehicle. See Passive Anti-Theft System (page 61).

Press the button once. The

image475

parking lamps turn off.

E138625

46

image476image477

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image478image479

MyKey™

image480

PRINCIPLE OF OPERATION

MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes.

Any keys that have not been programmed are referred to as administrator keys or admin keys. They can be used to:

Create a MyKey.
Program configurable MyKey settings.
Driver assist features, if equipped on your vehicle, are forced on: parking aid, blind spot information system (BLIS), cross traffic alert, lane departure warning and forward collision warning system.
Satellite radio adult content restrictions (available only in some markets).

Note: When you switch lane departure warning off temporarily, it turns on at the next ignition cycle.

Clear all MyKey features.

When you have programmed a MyKey, you can access the following information using the information display:

How many admin keys and MyKeys are programmed to your vehicle.
The total distance your vehicle has traveled using a MyKey.

Note: All MyKeys are programmed to the same settings. You cannot program them individually.

Note: For vehicles equipped with a push-button start switch: When both a MyKey and an admin key are present when you start your vehicle, the system recognizes the admin key only.

Non-configurable Settings

The following settings cannot be changed by an admin key user:

Belt-Minder or safety belt reminder. You cannot disable this feature. The audio system will mute when the front seat occupants’ safety belts are not fastened.
Early low fuel. The low fuel warning is activated earlier, giving the MyKey user more time to refuel.

47

image481

Configurable Settings

With an admin key, you can configure certain MyKey settings when you first create a MyKey and before you recycle the key or restart the vehicle. You can also change the settings afterward with an admin key:

A vehicle speed limit can be set. Warnings will be shown in the display, followed by an audible tone when your vehicle reaches the set speed. You cannot override the set speed by fully depressing the accelerator pedal or by setting cruise control.

WARNING

image482

Do not set MyKey maximum speed limit to a limit that will prevent the driver from maintaining a safe speed

image483

considering posted speed limits and prevailing road conditions. The driver is always responsible to drive in accordance with local laws and prevailing conditions. Failure to do so could result in accident or injury.

image484image485

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image486image487

MyKey™

image488

Various vehicle speed reminders so you know when your vehicle approaches the limits. Warnings appear in the information display and an audible warning sounds when you exceed the limit.
Audio system maximum volume of 45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed-sensitive or compensated automatic volume control will be disabled.
Always on setting. When this is selected, you will not be able to turn off Advance Trac or traction control, 911 Assist or Emergency Assistance, or Do Not Disturb (if your vehicle is equipped with these features).

image489

CREATING A MYKEY

Use the information display to create a

MyKey:

1.Insert the key you want to program into the ignition. See Starting a Gasoline Engine (page 145). If your vehicle is equipped with a push-button start, place the remote control into the backup position. See Passive Anti-Theft System (page 61).
2.Switch the ignition on.
3.Access the main menu on the information display controls. Use the arrow keys to get to the following menu selections:

image490

Message  image491 Action and Description

image492 Settings

image493

image494 MyKey

image495

image496 Create MyKey

image497

When prompted, hold the OK button until you see a message informing you to label this key as a MyKey. The key will be restricted at the next start.

MyKey is successfully created. Make sure you label it so you can distinguish it from the admin keys.

You can also program configurable settings for the key(s). See

Programming/Changing Configurable Settings.

Message

image498 Press the OK button or the right arrow key. image499

image500

image501 Press the OK button or the right arrow key. image502image503 Press the OK button or the right arrow key. image504

image505image506

Programming/Changing Configurable Settings

Use the information display to access your configurable MyKey settings.

1.Switch the ignition on using an admin key or remote control.
2.Access the main menu on the information display controls. Use the arrow keys to get to the following menu selections:

image507

Action and Description

Settings

Press the OK button or the right arrow key.

MyKey

Press the OK button or the right arrow key.

48

image508image509

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image510image511

MyKey™

image512

Note: You can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey. Once you have switched the vehicle off, however, you will need an admin key to change or clear your MyKey settings.

CLEARING ALL MYKEYS

You can clear or change your MyKey settings using the information display control on the steering wheel. See Information Displays (page 91).

Switch the ignition on using an admin key.

To clear all MyKeys of all MyKey settings, press the left arrow button to access the main menu and scroll to:

image513

Message  image514 Action and Description

image515 Settings image516 Press the OK button or the right arrow button.

image517 MyKey image518 Press the OK button or the right arrow button.

Clear MyKey  Press and hold the OK button until the instrument cluster

displays the following message.

All MyKeys

Cleared

Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status.

49

image519image520

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image521image522

MyKey™

image523

CHECKING MYKEY SYSTEM STATUS

You can find information on programmed MyKey(s) using the information display control on the steering wheel. See Information Displays (page 91).

To find information on programmed MyKey(s), press the left arrow button to access the main menu and scroll to:

image524

Message  image525 Description

image526 Settings image527 Press the OK button.

image528 MyKey image529 Press the OK button.

image530 Select one of the following:

MyKey Dist.  Tracks the distance when drivers use a MyKey. The only way

to delete the accumulated distance is by using an admin key to clear your MyKeys. If the distance does not accumulate as expected, then the intended user is not using the MyKey, or an admin key user recently cleared and then recreated a MyKey.

{0} MyKeys  Indicates the number of MyKeys programmed to your vehicle.

Use this feature to detect how many MyKeys you have for your vehicle and determine when a MyKey has been deleted.

{0} Admin Keys  Indicates how many admin keys are programmed to your

vehicle. Use this feature to determine how many unrestricted keys you have for your vehicle, and detect if an additional MyKey has been programmed.

50

image531image532

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image533image534

MyKey™

image535

USING MYKEY WITH REMOTE START SYSTEMS

MyKey is not compatible with non

Ford-approved, aftermarket remote start systems. If you choose to install a remote start system, see an authorized dealer for a Ford-approved remote start system.

MYKEY TROUBLESHOOTING

image536

Condition  image537 Potential Causes

I cannot create a MyKey.

I cannot program the configurable settings.

I cannot clear the MyKeys.

I lost the only admin key.

The key or transmitter used to start the vehicle does not have admin privileges.

Vehicles with keyless start: Make sure you place the transmitter into the backup position. See Starting a Gasoline Engine (page 145).

The key or transmitter used to start the vehicle is the only admin key. There always has to be at least one admin key.

The passive anti-theft system is disabled or in unlimited mode.

The transmitter used to start your vehicle does not have admin privileges.

There are no MyKeys programmed to the vehicle. See Creating a MyKey (page 48).

The key or transmitter used to start the vehicle does not have admin privileges.

No MyKeys are created. See Creating a MyKey (page 48).

Purchase a new key or transmitter from an authorized dealer.

I lost a key.  Program a spare key or transmitter. You may

need to see an authorized dealer. See Passive Anti-Theft System (page 61).

The MyKey distance does not accumu-late.

No MyKey functions with the trans-mitter.

The MyKey user is not using the MyKey.

An admin key holder cleared the MyKeys and created new MyKeys.

The key system has been reset.

An admin transmitter is present at vehicle start. There are no MyKeys programmed to your vehicle. See Creating a MyKey (page 48).

51

image538image539

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image540image541

Doors and Locks

image542

LOCKING AND UNLOCKING

You can use the power door lock control or the remote control to lock and unlock your vehicle.

unlocking mode applies to the remote control, keyless entry keypad and intelligent access. You can also change between the unlocking modes using the information display. See Information Displays (page 91).

Power Door Locks

The power door lock control is on the driver and front passenger door panels.

image543

A  B

E163049

AUnlock.

Locking the Doors

Press the button to lock all

doors. The direction indicators

E138623

will flash.

image544

Press the button again within three seconds to confirm that all the doors are closed. The doors will lock again, the horn will sound and the direction indicators will flash if all the doors and the liftgate are closed.

Note: If the system does not function, use the key blade to lock and unlock your vehicle.

BLock.

Remote Control (If Equipped)

Unlocking the Doors (Two-Stage Unlock)

Press the button to unlock the driver door.

image545

E138629

Press the button again within three seconds to unlock all doors. The direction indicators will flash.

Press and hold both the lock and unlock buttons on the remote control for three seconds to change between driver door or all doors unlock mode. The direction indicators flash twice to indicate a change to the unlocking mode. Driver door unlock mode only unlocks the driver door when you press the unlock button once. All door unlock mode unlocks all doors when you press the unlock button once. The

image546

Mislock

If any door or the liftgate is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the horn sounds twice and the direction indicators do not flash. You can switch this feature on or off in the information display. See Information Displays (page 91).

Opening the Liftgate

Press twice within three seconds to open the liftgate.

image547

E138630

Activating Intelligent Access (If

Equipped)

The intelligent access key must be within 3 ft (1 m) of the driver door or liftgate.

At a Door

You can use the keyless entry keypad to lock and unlock the doors. See Keyless Entry (page 58).

52

image548

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image549image550

Doors and Locks

image551

At the Liftgate

The liftgate unlocks and opens automatically when you press the liftgate release button.

Smart Unlocks for Integrated Keyhead Transmitter (If Equipped)

This helps to prevent you from locking yourself out of your vehicle if the key is still in the ignition.

When you open one of the front doors and lock your vehicle with the power door lock control, all the doors will lock then unlock and the horn will sound twice if the key is still in the ignition.

Your can still lock your vehicle with the key in the ignition by:

Using the manual lock on the door.
Locking the driver door with a key.

To do this, lock your vehicle after you have closed all the doors by:

Using the keyless entry keypad.
Pressing the lock button on another intelligent access key.

When you open one of the front doors and lock your vehicle using the power door lock control, all doors will lock then unlock if:

The ignition is on.
The ignition is off and the transmission is not in park (P).

Auto Relock

If you press the unlock button on the remote control and do not open a door within 45 seconds, your vehicle will lock and the alarm will arm. You can switch this feature on or off in the information display. See Information Displays (page 91).

Using the keyless entry keypad.
Pressing the lock button on another remote control.

Smart Unlocks for Intelligent

Access Keys (If Equipped)

This helps to prevent you from locking your key inside the passenger compartment or rear cargo area.

When you electronically lock your vehicle with any door open, the transmission is in park (P) and the ignition is off, the system searches for an intelligent access key inside your vehicle after you close the last door. If the system finds a key, all of the doors will immediately unlock and the horn will sound twice, indicating that a key is inside.

You can override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle.

53

image552

Autolock

Autolock locks all the doors when all of the following occur:

All doors are closed.
The ignition is on.
You shift into any gear putting your vehicle in motion.
Your vehicle’s speed is greater than 12 mph (20 km/h).

Autolock repeats when:

You open then close any door while the ignition is on and your vehicle’s speed is less than 9 mph (15 km/h).
Your vehicle’s speed is greater than 12 mph (20 km/h).

image553

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image554image555

Doors and Locks

image556

Autounlock

Autounlock unlocks all the doors when all of the following occur:

The ignition is on, all the doors are closed, and your vehicle has been moving at a speed greater than 12 mph (20 km/h).
You stop your vehicle and switch the ignition off or to accessory.
You open the driver door within 10 minutes of switching the ignition off or to accessory.

Note: The doors do not autounlock if you electronically lock your vehicle after you switch the ignition off and before you open the driver door.

The lamps will turn off if all the doors remain closed and:

25 seconds have elapsed.
You press the push button ignition switch.

Battery Saver

If you leave the courtesy lamps, interior lamps or headlamps on, the battery saver shuts them off 10 minutes after you switch the ignition off.

Battery Saver for Intelligent Access Keys (If Equipped)

If you leave the ignition switched on, it shuts off when it detects a certain amount of battery drain, or after 45 minutes.

Enabling or Disabling Autolock and Autounlock

You can enable or disable autolock and autounlock in the information display or an authorized dealer can do it for you. See General Information (page 91).

Illuminated Entry

The interior lamps and some exterior lamps illuminate when you unlock the doors with the remote control.

The lamps turn off if:

The ignition is on.
You press the remote control lock button.
25 seconds have elapsed.

The lamps do not turn off if:

You turn them on with the lamp control.
Any door is open.

Illuminated Exit

The interior lamps and some exterior lamps illuminate when all doors are closed and you switch the ignition off.

MANUAL LIFTGATE (If Equipped)

WARNINGS

image557

It is extremely dangerous to ride in a cargo area, inside or outside of your vehicle. In a crash, people riding in

image558

these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Make sure everyone in your vehicle is in a seat and properly using a safety belt. Failure to follow this warning could result in serious personal injury or death.

Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also

image559

prevent passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents or windows open so outside air comes into your vehicle. Failure to follow this warning could result in serious personal injury.

image560

54

image561image562

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image563image564

Doors and Locks

image565

Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate.

Note: Do not hang anything, for example a bike rack, from the glass or liftgate. This could damage the liftgate and its components.

Note: Do not leave the liftgate open while driving. This could damage the liftgate and its components.

Opening the Liftgate

Manually Opening the Liftgate

image566

E209081

With the Remote Control

Press twice within three seconds to unlatch the liftgate.

image567

E138630

Opening the Liftgate Window

image568

E209080

1.Press the release button.
2.Pull the liftgate glass upward.
1.Press the button inside the liftgate handle.
2.Pull the liftgate upward.

55

image569image570

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image571image572

Doors and Locks

image573

Closing the Liftgate  WARNINGS

image574

E209082

image575

A handle is located inside the liftgate to help with closing.

POWER LIFTGATE (If Equipped)

WARNINGS

image576

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in

image577

these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seatbelts. Make sure everyone in your vehicle is in a seat and properly using a seatbelt. Failure to follow this warning could result in serious personal injury or death.

Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also

image578

prevent passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents or windows open so outside air comes into your vehicle. Failure to follow this warning could result in serious personal injury.

56

image579

Keep keys out of reach of children. Do not allow children to operate or play near an open or moving power

image580

liftgate. You should supervise the operation of the power liftgate at all times.

image581

Note: Make sure that you close the liftgate before operating or moving your vehicle, especially in an enclosure, like a garage or a parking structure. This could damage the liftgate and its components.

Note: Do not hang anything, for example a bike rack, from the glass or liftgate. This could damage the liftgate and its components.

The liftgate only operates with the transmission in park (P).

Three warning tones sound as the liftgate begins to power close. If there is a problem with the open or close request, one of the following may occur:

One chime sounds if the ignition is on and the transmission is not in park (P).
Three chimes sound if the battery voltage is below the minimum operating voltage.
One chime sounds if the vehicle speed is at or above 3 mph (5 km/h).

If the liftgate starts to close after it has fully opened, this indicates there may be excessive weight on the liftgate or a possible strut failure. A repetitive tone sounds and the liftgate closes under control. Remove any excessive weight from the liftgate. If the liftgate continues to close after opening, have the system checked by an authorized dealer.

image582

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image583image584

Doors and Locks

image585

Opening and Closing the Liftgate

WARNING

image586

Make sure all persons are clear of the power liftgate area before using the power liftgate control.

image587image588

Note: Make sure the area behind your vehicle is free from obstruction and that there is enough room for you to operate the liftgate. Objects too close to your vehicle, for example a wall, garage door or another vehicle may come into contact with the moving liftgate. This could damage the liftgate and its components.

Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate.

Note: Do not leave the liftgate open while driving. This could damage the liftgate and its components.

From the Instrument Panel

Press the button on the instrument panel.

image589

E209081

image590

2.Press the button inside the liftgate handle.

With the Remote Control

Press the button twice within three seconds.

image591

E138630

With the Outside Control Button Opening the Liftgate

1.Unlock the liftgate with the remote control or power door unlock control. If an intelligent access key is within 3 ft (1 m) of the liftgate, the liftgate unlocks when you press the liftgate release button.

57

image592

Note: Allow the system to open the liftgate. Manually pushing or pulling the liftgate may turn on obstacle detection and stop the power operation or reverse its direction. Manually interfering with the liftgate motion may also replicate a strut failure.

Closing the Liftgate

WARNING

image593

Keep clear of the liftgate when activating the rear switch.

image594image595image596

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image597image598

Doors and Locks

image599

E209084

image600

Press and release the button in the rear cargo area.

Obstacle Detection

When Closing

The system stops when it detects an obstacle. Three chimes sound and the system reverses to open. Once you remove the obstacle, you can power close the liftgate.

Note: Entering your vehicle while the liftgate is closing can cause your vehicle to bounce and activate obstacle detection. To prevent this, let the power liftgate close completely before you enter your vehicle. Before driving off, check the instrument cluster for a liftgate or door ajar message or warning indicator. Failure to do this could result in unintentionally leaving the liftgate open while driving.

When Opening

The system stops when it detects an obstacle and two short tones sound. Remove the obstacle to operate the liftgate.

KEYLESS ENTRY

Stopping the Liftgate Movement

Note: Do not apply sudden excessive force to the liftgate while it is in motion. This could damage the power liftgate and its components.

You can stop the liftgate movement by doing any of the following:

Pressing the liftgate control button.
Pressing the liftgate button on the remote control twice.
Pressing the liftgate button on the instrument panel.

SECURICODE™ KEYLESS ENTRY KEYPAD

The keypad is located near the driver window.

Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more slowly.

image601

E163050

58

image602image603

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image604image605

Doors and Locks

image606

You can use the keypad to lock or unlock the doors without using a key.

For vehicles without intelligent access, you can operate the keypad with the factory-set 5-digit entry code. The code is located on the owner’s wallet card in the glove box and is available from an authorized dealer. You can also create up to five of your own 5-digit personal entry codes.

For vehicles with intelligent access, you do not need to enter a 5-digit entry code. Press any button on keyless entry keypad once to unlock all doors.

Note: You must have an intelligent access key within 3 ft (1 m) of your vehicle.

Programming a Personal Entry Code

To create your own personal entry code:

1.Enter the factory-set code.
2.Press 1·2 on the keypad within five seconds.
3.Enter your personal 5-digit code. You must enter each number within five seconds of each other.
4.Press 1·2 on the keypad to save personal code 1.

The doors will lock then unlock to confirm that programming was successful.

To program additional personal entry codes, repeat Steps 1-3, then for Step 4:

press 3·4 to save personal code 2
press 5·6 to save personal code 3
press 7·8 to save personal code 4
press 9·0 to save personal code 5.

You may also program a personal entry code through the information display.

Tips:

Do not set a code that uses five of the same number.
Do not use five numbers in sequential order.
The factory-set code will work even if you have set your own personal code.

Recalling Memory Positions (If Equipped)

The programmed entry codes will recall driver memory positions as follows:

Entry code 1 will recall driver 1 memory positions.
Entry code 2 will recall driver 2 memory positions.

Note: Personal entry codes 3, 4 and 5 will not recall memory positions.

Erasing a Personal Code

1.Enter the factory-set 5-digit code.
2.Press and release 1·2 on the keypad within five seconds.
3.Press and hold 1·2 for two seconds. You must do this within five seconds of completing Step 2.

All personal codes will erase and only the factory-set 5-digit code will work.

Anti-Scan Feature

The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp will flash.

The anti-scan feature will turn off after:

one minute of keypad inactivity
pressing the unlock button on the remote control
switching the ignition on.

59

image607image608

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image609image610

Doors and Locks

image611

Displaying the Factory Set Code

Note: You need to have two programmed keys for this procedure.

To display the factory-set code in the

information display:

1.Insert a key into the ignition and switch the ignition on for a few seconds.
2.Switch the ignition off and remove the key.
3.Insert the second key into the ignition and switch the ignition on.

The factory-set code will display for a few seconds.

Note: The code may not display until after any other warning messages first display.

Unlocking and Locking the Doors

Vehicles Without Intelligent Access

To Unlock the Driver Door

Enter the factory-set 5-digit code or your personal code. You must press each number within five seconds of each other. The interior lamps will illuminate.

Note: All doors will unlock if you disable the two-stage unlocking mode. See Locking and Unlocking (page 52).

To Unlock All Doors

Enter the factory-set code or your personal code, then press 3·4 within five seconds.

To Lock All Doors

Press and hold 7·8 and 9·0 at the same time (with the driver door closed). You do not need to enter the keypad code first.

Vehicles With Intelligent Access

Press any button on keyless entry keypad once to unlock all doors.

Note: You must have an intelligent access key within 3 ft (1 m) of your vehicle.

60

image612image613

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image614image615

Security

image616

PASSIVE ANTI-THEFT SYSTEM

Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.

Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting problems if they are too close to the key when starting the engine. Prevent these objects from touching the coded key while starting the engine. Switch the ignition off, move all objects on the key chain away from the coded key and restart the engine if a problem occurs.

Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle.

SecuriLock®

The system is an engine immobilization system. It is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. Using the wrong key may prevent the engine from starting. A message may appear in the information display.

If you are unable to start the engine with a correctly coded key, a malfunction has happened and a message may appear in the information display.

Automatic Arming

The vehicle arms immediately after you switch the ignition off.

Automatic Disarming

Switching the ignition on with a coded key disarms the vehicle.

61

image617

Replacement Keys

Note: Your vehicle comes equipped with two integrated keyhead transmitters or two intelligent access keys.

The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote control.

The intelligent access key functions as a programmed key that operates the driver door lock and activates the intelligent access with push button start system, as well as a remote control.

If your programmed transmitters or standard SecuriLock coded keys (integrated keyhead transmitters only) are lost or stolen and you do not have an extra coded key, you will need to have your vehicle towed to an authorized dealer. You need to erase the key codes from your vehicle and program new coded keys.

Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. See your authorized dealer to purchase additional spare or replacement keys.

Programming a Spare Integrated Keyhead Transmitter

Note: You can program a maximum of eight coded keys to your vehicle. All eight can be integrated keyhead transmitters.

You can program your own integrated keyhead transmitter or standard SecuriLock coded keys to your vehicle. This procedure will program both the engine immobilizer keycode and the remote entry portion of the remote control to your vehicle

Only use integrated keyhead transmitters or standard SecuriLock keys.

image618

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image619image620

Security

image621

You must have two previously programmed coded keys and the new unprogrammed key readily accessible. See your authorized dealer to have the spare key programmed if two previously programmed coded keys are not available.

Read and understand the entire procedure before you begin.

1.Insert the first previously programmed coded key into the ignition.
2.Switch the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds.
3.Switch the ignition off and remove the first coded key from the ignition.
4.After three seconds but within 10 seconds of switching the ignition off, insert the second previously coded key into the ignition.
5.Switch the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds.
6.Switch the ignition off and remove the second previously programmed coded key from the ignition.
7.After three seconds but within 10 seconds of switching the ignition off and removing the previously programmed coded key, insert the new unprogrammed key into the ignition.
8.Switch the ignition from off to on. Keep the ignition on for at least six seconds.
9.Remove the newly programmed coded key from the ignition.

If the key has been successfully programmed it will start the engine and operate the remote entry system (if the new key is an integrated keyhead transmitter).

If programming was not successful, wait 10 seconds and repeat Steps 1 through 8. If you are still unsuccessful, take your vehicle to your authorized dealer.

62

image622

Programming a Spare Intelligent Access Key

See your authorized dealer to have additional keys programmed to your vehicle.

ANTI-THEFT ALARM

The system will warn you of an unauthorized entry to your vehicle. It will be triggered if any door, the luggage compartment or the hood is opened without using the key, remote control or keyless entry keypad.

The direction indicators will flash and the horn will sound if unauthorized entry is attempted while the alarm is armed.

Take all remote controls to an authorized dealer if there is any potential alarm problem with your vehicle.

Arming the Alarm

The alarm is ready to arm when there is not a key in your vehicle. Electronically lock your vehicle to arm the alarm.

Disarming the Alarm

Disarm the alarm by any of the following actions:

Unlock the doors or luggage compartment with the remote control or keyless entry keypad.
Switch your vehicle on or start your vehicle.
Use a key in the driver door to unlock your vehicle, then switch your vehicle on within 12 seconds.

Note: Pressing the panic button on the remote control will stop the horn and signal indicators, but will not disarm the system.

image623

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image624image625

Power Running Boards (If Equipped)

image626

USING POWER RUNNING BOARDS

WARNINGS

image627

In extreme climates, excessive ice buildup may occur, causing the running boards not to deploy. Make

image628

sure that the running boards have deployed, and have finished moving before attempting to step on them. The running boards will resume normal function once the blockage is cleared.

Turn off the running boards before jacking or placing any object under your vehicle. Never place your hand

image629

between the extended running board and your vehicle. A moving running board may cause injury.

image630

Note: Do not use the running boards, front and rear hinge assemblies, running board motors, or the running board underbody mounts to lift your vehicle when jacking. Always use proper jacking points.

Note: The running boards may operate more slowly in cool temperatures.

Note: The running board mechanism may trap debris such as mud, dirt, snow, ice and salt. This may cause unwanted noise. If this happens, manually set the running boards to the deployed position. Then, wash the system, in particular the front and rear hinge arms, with a high-pressure car wash wand.

Automatic Power Deploy

image631

E166682

The running boards automatically extend down and out when you open the door. This can help you enter and exit your vehicle.

Automatic Power Stow

When you close the doors, the running boards return to the stowed position after a two-second delay.

Manual Power Deploy

You can manually operate the running boards in the information display. See General Information (page 91).

Set the running boards in the deployed position to access the roof.

The running boards return to the stowed position and enter automatic mode when the vehicle speed exceeds 5 mph (8 km/h).

Enabling and Disabling

You can enable and disable the power

running board feature in the information

display. See General Information (page

91).

63

image632image633

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image634image635

Power Running Boards (If Equipped)

image636

When disabled (OFF), the running boards move to the stowed position regardless of the door position.
When enabled (AUTO), the running boards move back to the correct positions based on the door position.

Bounce-back

The running board will reverse direction

and move to the end of travel if it

encounters an object while moving.

64

image637image638

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image639image640

Steering Wheel

image641

ADJUSTING THE STEERING WHEEL – VEHICLES WITH: COLUMN SHIFT/MANUAL ADJUSTABLE STEERING COLUMN

image642

WARNING

image643

Do not adjust the steering wheel when your vehicle is moving.

image644image645

Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 121).

image646

E205804

1.Unlock the steering column.
2.Adjust the steering wheel to the desired position.

65

image647

E183049

3.  Lock the steering column.

ADJUSTING THE STEERING WHEEL – VEHICLES WITH: FLOOR SHIFT/MANUAL ADJUSTABLE STEERING COLUMN

WARNING

image648

Do not adjust the steering wheel when your vehicle is moving.

image649image650

Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 121).

image651

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image652image653

Steering Wheel

image654

ADJUSTING THE STEERING WHEEL – VEHICLES WITH:

image655

POWER ADJUSTABLE STEERING COLUMN

Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 121).

WARNING

image656

Do not adjust the steering wheel when your vehicle is moving.

image657

E183047

1.Unlock the steering column.
2.Adjust the steering wheel to the desired position.

image658

E183049

3.  Lock the steering column.

E161834

Use the control on the side of the steering column to adjust the position.

To adjust:

Tilt: Press the top or bottom of the control.
Telescope: Press the front or rear of the control.

66

image659image660

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image661image662

Steering Wheel

image663

End of Travel Position  AUDIO CONTROL (If Equipped)

The steering column sets a stopping position just short of the end of the column position to prevent damage to the steering column. A new stopping position sets if the steering column encounters an object when tilting or telescoping.

To reset the steering column to its normal stopping position:

1.Confirm there is nothing obstructing the motion of the steering column.
2.Press and hold the steering column control until the steering column stops moving.
3.Press the steering column control again. The steering column may begin to move again.
4.When the steering column stops, continue holding the control for an additional few seconds.
5.Repeat for each direction as necessary.

A new stopping position is set. The next time you tilt or telescope the steering column, it will stop just short of the end of the column position.

Operate the following functions with the control:

Type One

image664

Memory Feature

You can save and recall the steering column position with the memory function. See Memory Function (page 125).

Note: Pressing the adjustment control during memory recall cancels the operation.

Easy Entry and Exit Feature

When you switch the ignition off, the steering column will move to allow extra room to exit your vehicle. The column will return to the previous setting when you switch the ignition on. You can enable or disable this feature in the information display. See Information Displays (page 91).

67

image665

E205755

AVolume up.
BSeek up or next.
CSeek down or previous. D Volume down.

image666

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image667image668

Steering Wheel

image669

Type Two  Press and hold the seek button to:

  Tune the radio to the next station up or down the frequency band.

image670

  Seek through a track.

VOICE CONTROL (If Equipped)

Type One

image671

E205756

AVolume up.
BSeek up or next. C Media.

D Seek down or previous. E Volume down.

Media

Press repeatedly to scroll through available audio sources.

Seek, Next or Previous

Press the seek button to:

Tune the radio to the next or previous stored preset.
Play the next or the previous track.

68

image672

E205757

APhone mode.
BVoice recognition.

See SYNC™ (page 324).

image673

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image674image675

Steering Wheel

image676

Type Two  CRUISE CONTROL

image677

E205805

See Cruise Control (page 187).

INFORMATION DISPLAY CONTROL

image678image679

E205758

APhone mode.
BVoice recognition.

See SYNC™ (page 324).

E205806

See Information Displays (page 91).

HEATED STEERING WHEEL (If

Equipped)

See your SYNC information.

69

image680image681

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image682image683

Pedals (If Equipped)

image684

ADJUSTING THE PEDALS

WARNING

image685

Never use the controls while your

image686

feet are on the accelerator and brake

pedals and the vehicle is moving.

image687

You can find the control on the left side of the steering column. Press and hold the appropriate side of the control to move the pedals.

image688

A  B

E162916

A.Farther
B.Closer

You can save and recall the pedal positions with the memory feature. See Memory Function (page 125).

Note: Adjust the pedals only when your

vehicle is in P (Park).

70

image689image690

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image691image692

Wipers and Washers

image693

WINDSHIELD WIPERS

Note: Fully defrost the windshield before you switch the windshield wipers on.

Note: Make sure you switch the windshield wipers off before entering a car wash.

Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. See Changing the Wiper Blades (page 255).

Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield.

image694

E205527

Rotate the end of the control:

Away from you to increase the wiper speed.
Toward you to decrease the wiper speed.

Speed Dependent Wipers

When your vehicle speed increases, the interval between wipes decreases.

AUTOWIPERS (If Equipped)

Note: Fully defrost the windshield before switching on the windshield wipers.

Note: Make sure you switch off the windshield wipers before entering a car wash.

71

image695

Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. See Changing the Wiper Blades (page 255).

Wet or winter driving conditions with ice, snow or salty road mist can cause inconsistent and unexpected wiping or smearing. In these conditions, you can do the following to help keep your windshield clear:

Lower the sensitivity of the autowipers to reduce the amount of smearing.
Switch to normal or high-speed wipe.
Switch the autowipers off.

The autowipers feature uses a rain sensor, located in the area around the interior mirror. The rain sensor monitors the amount of moisture on the windshield and automatically turns on the wipers. It adjusts the wiper speed by the amount of moisture that the sensor detects on the windshield.

Note: This autowiper feature is automatically set to on and remains on until you switch it off in the information display. You can also switch the feature back on at any time. See General Information (page 91).

Use the rotary control to adjust the sensitivity of the rain sensor. Set the control to low sensitivity, and the wipers will turn on when the rain sensor detects a large amount of moisture on the windshield. Set the control to high sensitivity, and the wipers will turn on when the rain sensor detects a small amount of moisture on the windshield.

Note: When you set the wiper system to intermittent wipe and the autowiper system is on, the autowiper sensitivity setting adjusts the wiper speed according to the moisture on the windshield only. Use the wiper lever to wipe the windshield on-demand.

image696

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image697image698

Wipers and Washers

image699

Keep the outside of the windshield clean. The rain sensor is very sensitive. If the area around the mirror is dirty, then the wipers may operate if dirt, mist or insects hit the windshield.

WINDSHIELD WASHERS

Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield.

Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat.

REAR WINDOW WIPER AND WASHERS

Rear Window Wiper

Note: Make sure you switch off the wiper system before using an automatic car wash.

image700

E205529

Rotate the control to select:

E205528

image701

Press the end of the wiper lever to activate the washer:

A brief press causes a single wipe without washer fluid.
A quick press and hold causes the wipers to swipe the windshield three times with washer fluid.
A long press and hold activates the wipers and washer fluid for up to 10 seconds.

A wipe occurs a few seconds after washing to clear any remaining washer fluid. You can switch this feature on and off through the information display. See Information Displays (page 91).

72

image702

2Intermittent operation – the shortest pause between wipes.
1Intermittent operation – the longest pause between wipes.
0Off.

Rear Window Washer

image703

E205529

Rotate and hold the control to the top or bottom position to activate the rear washer. The control returns to the 2 or 0 position when you release it.

image704

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image705image706

Lighting

image707

GENERAL INFORMATION

Condensation in Lamp Assemblies

Exterior lamps have vents to accommodate normal changes in air pressure.

Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens. The fine mist eventually clears and exits through the vents during normal operation.

Clearing time may take as long as 48 hours under dry weather conditions.

Examples of acceptable condensation are:

The presence of a fine mist (no streaks, drip marks or large droplets).
A fine mist covers less than 50% of the lens.

Examples of unacceptable condensation are:

A water puddle inside the lamp.
Streaks, drip marks or large droplets present on the interior of the lens.

If you see any unacceptable condensation, have your vehicle checked by an authorized dealer.

LIGHTING CONTROL

image708

E245147

AOff.
BParking lamps, instrument panel, license plate lamps and tail lamps.
CHeadlamps.

High Beams

image709

E167827

Push the lever away from you to switch

the high beam on.

Push the lever away from you again or pull

the lever toward you to switch the high

beam off.

73

image710image711

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image712image713

Lighting

image714

Headlamp Flasher

image715

E163268

Slightly pull the lever toward you and release it to flash the headlamps.

When the lighting control is in the autolamps position, the headlamps automatically turn on in low light situations or when the wipers turn on.

When the lighting control is in the autolamps position, you can switch on the following in the information display:

Configurable daytime running lamps.
Automatic high beam control.
Adaptive headlamp control.

The headlamps remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps remain on. See Information Displays (page 91).

AUTOLAMPS – VEHICLES WITH: AUTOLAMPS

WARNING

image716

The autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime

image717

fog. Always ensure that your headlamps are switched to auto or on, as appropriate, during all low visibility conditions. Failure to do so may result in a crash.

image718

Note: With the headlamps in the autolamps position, you cannot switch the high beam headlamps on until the autolamps system turns the low beam headlamps on.

Windshield Wiper Activated Headlamps

When you switch the autolamps on, the windshield wiper activated headlamps turn on within 10 seconds of switching on the wipers. They turn off approximately 60 seconds after you switch the windshield wipers off.

The headlamps do not turn on with the wipers:

During a mist wipe.
When the wipers are on to clear washer fluid during a wash condition.
If the wipers are in intermittent mode.

E245149

74

image719

Note: If you switch autolamps and autowipers on, the headlamps will automatically turn on when the windshield wipers continuously operate.

image720

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image721image722

Lighting

image723

INSTRUMENT LIGHTING

DAYTIME RUNNING LAMPS (If

DIMMER

Equipped)

WARNING

image724

E163270

Use to adjust the brightness of the instrument panel and all applicable lit components in the vehicle during headlamp and parking lamp operation.

Tap the top or bottom of the control to brighten/dim all interior lit components incrementally, or
Press and hold at the first position the top or bottom of the control until the desired lighting level is reached.
Press and hold the top of the control to the full on position to activate the “dome on” feature. This will turn on the interior courtesy lights. The lights will remain on until the bottom of the control is pressed.

75

image725

The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting

image726image727

during low visibility driving conditions. Also, the autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog. Make sure the headlamps are switched to auto or on, as appropriate, during all low visibility conditions. Failure to do so may result in a crash.

image728

Type 1 – Conventional (Non-Configurable)

The daytime running lamps turn on when:

1.The ignition is switched to the on position.
2.The transmission is not in park (P) for vehicles with automatic transmissions or the parking brake is released for vehicles with manual transmissions.
3.The lighting control is in the off, parking lamp or autolamps positions.
4.The headlamps are off.

Type 2 – Configurable

Switch the daytime running lamps on or off using the information display controls. See Information Displays (page 91).

The daytime running lamps turn on when:

1.They are switched on in the information display. See Information Displays (page 91).
2.The ignition is switched to the on position.

image729

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image730image731

Lighting

image732

3.The transmission is not in park (P) for vehicles with automatic transmissions or the parking brake is released for vehicles with manual transmissions.
4.The lighting control is in the autolamps position.
5.The headlamps are off.

The other lighting control switch positions do not activate the daytime running lamps, and you can use them to temporarily override autolamp control.

When switched off in the information display, the daytime running lamps are off in all lighting control switch positions.

FRONT FOG LAMPS

image733

DIRECTION INDICATORS

image734

E163272

To operate the left-hand direction indicator, push the lever down until it stops.
To operate the right-hand direction indicator, push the lever up until it stops.
To manually cancel direction indicator operation, push the lever again in either direction.

E245148

Push the lighting control down to switch the fog lamps on.

You can switch the fog lamps on when the lighting control is in any position except off and the high beams are not on.

image735

Lane Change

To indicate a left or right lane change:

Push the lever up or down to the first stop position and release. The direction indicator will flash three times and stop.
Push the lever up or down to the first stop position and hold. The direction indicator will flash for as long as you hold the lever in this position.

76

image736

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image737image738

Lighting

image739

INTERIOR LAMPS

Front Row Map Lamps (If Equipped)

Press the switches on either side of each map lamp to turn on the lamps. The map lamps light when:

any door is opened.
the instrument panel dimmer switch is pressed up until the courtesy lamps come on.
any of the remote entry controls are pressed and the ignition is off.

image740

E163273

E163274

image741

Second Row Map Lamps (If Equipped)

The map lamps are located in the headliner above the second row seats. The map lamps light when:

any door is opened.
the instrument panel dimmer switch is pressed up until the courtesy lamps come on.
any of the remote entry controls are pressed and the ignition is off.

Press the controls to activate the lamps.

Front Row Map and Dome Lamps

(If Equipped)

image742

Press the switches on either side of the dome lamp to turn on the lamps. The dome lamp lights when:

any door is opened.
the instrument panel dimmer switch is pressed up until the courtesy lamps come on.
any of the remote entry controls are pressed and the ignition is off.

image743

E206071

77

image744

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image745image746

Lighting

image747

Rear Cargo Lamp

The rear cargo lamps light when:

any door is opened, and the switch is in the middle position.
the instrument panel dimmer switch is pressed up until the courtesy lamps come on.
any of the remote entry controls are pressed and the ignition is off (and the switch is in the middle position).

With the ignition key in the accessory or on position, the rear cargo lamp can be turned on or off by sliding the control.

image748

E206072

Battery Saver

The battery saver will shut off the exterior lamps and interior lamps, except the hazard warning lamps if activated, 10 minutes after the ignition control has been turned off. The system will not turn off the parking lamps if the lighting control is in the parking lamps on position.

AMBIENT LIGHTING (If Equipped)

Adjust the ambient lighting using the

touchscreen.

78

image749image750

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image751image752

Windows and Mirrors

image753

POWER WINDOWS

WARNINGS

image754

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

image755

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

image756

children and pets are not in the proximity of the window openings.

image757image758

E163056

Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise.

Press the control to open the window.

Lift the control to close the window.

One-Touch Down

Press the control fully and release it. Press again or lift it to stop the window.

One-Touch Up

Lift the control fully and release it. Press again or lift it to stop the window.

Overriding the Bounce-Back Feature

WARNING

image759

When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care

image760

when closing the windows to avoid personal injury or damage to your vehicle.

image761

Pull up the window switch and hold within a few seconds of the window reaching the bounce-back position. The window travels up with no bounce-back protection. The window will stop if you release the switch before the window fully closes.

Window Lock

image762

A  B

E163057

AUnlock.

B Lock.

Press the control to lock or unlock the rear window controls.

Accessory Delay

The window switches remain operational for several minutes when you switch the ignition off or until you open either front door.

Bounce-Back

The window will automatically stop and

reverse some distance if it detects an

obstacle while closing.

79

image763image764

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image765image766

Windows and Mirrors

image767

EXTERIOR MIRRORS

Power Exterior Mirrors

WARNING

image768

Do not adjust the mirrors when your vehicle is moving.

image769image770image771

image772 B image773

A  image774 C

E163059

ALeft-hand mirror.
BOff.
CRight-hand mirror.

To adjust a mirror:

1.Select the mirror you want to adjust.
2.Move the control in the direction you want to tilt the mirror.
3.Return the control to the center position to lock the mirrors in place.

Fold-Away Exterior Mirrors

Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position.

Power-Folding Mirrors (If Equipped)

image775

E163060

Note: Moving the mirrors 10 or more times within one minute, or repeated folding and unfolding of the mirrors while holding the control down during full travel, may disable the system to protect the motors from overheating. Wait approximately three minutes with the vehicle running, and up to 10 minutes with the vehicle off, for the system to reset and for function to return to normal.

Pull the control back to fold the mirrors in or out.

Loose Mirror

If you manually fold your power-folding mirrors, they may not work properly even after you re-position them. You need to reset them if:

The mirrors vibrate when you drive.
The mirrors feel loose.
The mirrors do not stay in the folded or unfolded position.
One of the mirrors is not in its normal driving position.

To reset the power-fold feature, use the

power-folding mirror control to fold and

unfold the mirrors. You may hear a loud

noise as you reset the power-folding

mirrors. This sound is normal. Repeat this

process as needed each time you manually

fold the mirrors.

80

image776image777

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image778image779

Windows and Mirrors

image780

Heated Exterior Mirrors

See Heated Windows and Mirrors (page 120).

Memory Mirrors (If Equipped)

You can save and recall the mirror positions through the memory function. See Memory Function (page 125).

Auto-Dimming Feature

The driver exterior mirror automatically dims with the auto-dimming interior mirror.

Signal Indicator Mirrors (If Equipped)

The outer portion of the appropriate mirror housing blinks when you switch on the direction indicator.

Blind Spot Monitor (If Equipped)

See Blind Spot Information System (page 189).

INTERIOR MIRROR

WARNING

image781

Do not adjust the mirror when your vehicle is moving.

image782image783

Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products.

You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side.

Auto-Dimming Mirror

Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor.

The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up.

CHILDMINDER MIRROR

On double bin overhead consoles, the conversation mirror allows the driver to view the rear seating area.

WARNING

image784

Do not use the childminder mirror to view rearward traffic, do not allow rear passengers to distract you from

image785

the driving task, and make sure the rear view mirror has a clear view of rearward traffic. Failure to do so could increase the risk of a crash from an unseen vehicle, which may result in serious injury.

image786image787

E205354

Press the release area on the rear edge of

the bin door to open the childminder mirror.

The door will open to full open position.

81

image788image789

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image790image791

Windows and Mirrors

image792

The rear view mirror may have to be adjusted to its lower arm position to prevent interference when the childminder mirror is extended down.

REAR QUARTER WINDOWS (If

Equipped)

WARNINGS

image793

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

image794

seriously injure themselves.

When closing the power windows, you should verify they are free of obstructions and make sure that

image795

children and pets are not in the proximity of the window openings.

image796image797

E205283

SUN VISORS

image798

E138666

Rotate the sun visor toward the side window and extend it rearward for extra shade.

Illuminated Vanity Mirror

image799

E162197

Press and hold the VENT control to open the rear quarter windows.

Pull and hold the VENT control to close the rear quarter windows.

Lift the cover to switch the lamp on.

MOONROOF (If Equipped)

Note: Vehicles without a moonroof will only have the VENT control.

82

image800

WARNINGS

image801

Do not let children play with the moonroof or leave them unattended in the vehicle. They may seriously

image802

hurt themselves.

image803

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image804image805

Windows and Mirrors

image806

WARNINGS

image807

When closing the moonroof, you should verify that it is free of obstructions and make sure that

image808

children and pets are not in the proximity of the roof opening.

image809

You can manually open or close the sliding shade when the moonroof is closed. Pull the shade toward the front of your vehicle to close it.

The moonroof controls are located on the overhead console and have a one-touch open and close feature. To stop it during one-touch operation, press the control a second time.

Bounce-Back

The moonroof will stop automatically while closing. It will reverse some distance if there is an obstacle in the way.

Pull and hold the SLIDE control within two seconds of a bounce-back event to override this function. While bounce-back is active, the closing force increases for each of the next three times that you close the moonroof.

Venting the Moonroof

Press and release the TILT control to vent the moonroof. Pull and hold the TILT control to close the moonroof.

Opening and Closing the Moonroof

image810

E163063

Press and release the SLIDE control to

open the moonroof. The moonroof will

stop short of the fully opened position.

Note: This position helps to reduce wind

noise or rumbling which may happen with

the moonroof fully open. Press and release

the control again to fully open the

moonroof.

Pull and release the SLIDE control to close

the moonroof.

83

image811image812

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image813image814

Instrument Cluster

image815

GAUGES

Type 1 and 2

image816

E205349

ATachometer.
BInformation display (Type 2 shown Type 1 similar). C Speedometer.

D Fuel gauge.

E Engine coolant temperature gauge.

Information Display

Odometer

Located in the bottom of the information display. Registers the accumulated distance your vehicle has traveled.

Outside Air Temperature

Shows the outside air temperature.

Trip Computer

See General Information (page 91).

84

image817image818

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image819image820

Instrument Cluster

image821

Vehicle Settings and Personalization See General Information (page 91).

Fuel Gauge

Note: The fuel gauge may vary slightly when your vehicle is moving or on a gradient.

Switch the ignition on. The fuel gauge indicates approximately how much fuel remains in the fuel tank. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located.

The needle should move toward F when you refuel your vehicle. If the needle points to E after adding fuel, this indicates your vehicle needs service soon.

After refueling, the needle may not always return to the exact same position. This is normal.

Note: It may take a short time for the needle to reach F after leaving the gas station. This is normal and depends upon the slope of pavement at the gas station.

Note: The fuel amount dispensed into the tank is a little less or more than the gauge indicated. This is normal and depends upon the slope of pavement at the gas station.

85

image822

Note: If the gas station nozzle shuts off before the tank is full, try a different gas pump nozzle.

Note: There is a small reserve left in the tank when the fuel gauge reaches empty.

Low Fuel Reminder

A low reminder displays when the distance to empty reaches 50 miles (80 km) to empty.

Note: The low fuel reminder can appear at different fuel gauge positions depending on fuel economy conditions. This variation is normal.

Engine Coolant Temperature Gauge

Shows the temperature of the engine coolant. At normal operating temperature, the needle remains in the center section. If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down.

Note: Do not restart the engine until you conclude the cause of overheating.

WARNING

image823

Never remove the coolant reservoir cap while the engine is running or hot. The hot coolant is under pressure

image824

and may cause serious burns.

image825image826

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image827image828

Instrument Cluster

image829

Type 3

image830

E205350

ALeft Information Display. B Speedometer.

C Right Information Display. See SYNC™ (page 324).

Left Information Display

Vehicle Settings and Personalization

See General Information (page 91).

Odometer

Located in the bottom of the information

display. Registers the accumulated

distance your vehicle has traveled.

Outside Air Temperature

Shows the outside air temperature.

Trip Computer

See General Information (page 91).

86

image831image832

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image833image834

Instrument Cluster

image835

WARNING LAMPS AND INDICATORS

The following warning lamps and indicators alert you to a vehicle condition that may become serious. Some lamps illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information.

Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle.

Anti-Lock Braking System

If it illuminates when you are driving, this indicates a

image836

malfunction. You continue to have the normal braking system (without ABS) unless the brake warning lamp is also illuminated. Have the system checked by an authorized dealer.

WARNING

image837

Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance

image838

may occur. It will take you longer to stop your vehicle. Have your vehicle checked as soon as possible. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury.

image839

Cruise Control

It illuminates when you switch

this feature on. See Using

E71340

Cruise Control (page 187).

image840

Direction Indicator

Illuminates when you switch the left or right direction indicator or the hazard warning flasher on. If

image841

the indicators stay on or flash faster, check for a burned out bulb.

Battery

If it illuminates while driving, it

image842

indicates a malfunction. Switch off all unnecessary electrical

equipment and have the system checked by an authorized dealer.

Brake System

It illuminates when you engage the parking brake and the

image843

E144522

ignition is on.

If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by an authorized dealer.

Door Ajar

Displays when the ignition is on and any door is not completely closed.

image844

Engine Coolant Temperature

Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as

image845

possible, switch off the engine and let cool.

See Engine Coolant Check (page 247).

87

image846image847

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image848image849

Instrument Cluster

image850

Engine Oil  Liftgate Ajar

If it illuminates with the engine running or when you are driving,

image851

this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 245).

Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by an authorized dealer.

Fasten Safety Belt

It illuminates and a chime

sounds to remind you to fasten

E71880

your safety belt.

image852

Front Airbag

If it fails to illuminate on startup,

continues to flash or remains on,

E67017

it indicates a malfunction. Have

image853

the system checked by an authorized dealer. A chime sounds when there is a malfunction in the indicator light.

Front Fog Lamps (If Equipped)

It illuminates when you switch the front fog lamps on.

image854

High Beam

It illuminates when you switch the headlamp high beam on. It

image855

flashes when you use the headlamp flasher.

Hill Descent (If Equipped)

Illuminates when you switch hill descent on.

image856image857

Lights when the liftgate is not completely closed.

image858

E162453

Low Fuel Level

It illuminates when the fuel level is low or near empty. Refuel as soon as possible.

image859

Low Tire Pressure Warning

It illuminates when your tire pressure is low. If the lamp remains on with the engine

image860

running or when driving, check your tire pressure as soon as possible.

The lamp also illuminates momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by an authorized dealer.

Low Washer Fluid

It illuminates when the windshield washer fluid is low.

image861

E132353

Parking Lamps

It illuminates when you switch the parking lamps on.

image862

Powertrain Fault

Illuminates when a powertrain fault has been detected. Contact an authorized dealer as soon as

image863

possible.

88

image864

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image865image866

Instrument Cluster

image867

Service Engine Soon  Stability Control System

If the service engine soon

image868

indicator light stays illuminated after you start the engine, it

indicates that the On Board Diagnostics system (OBD) has detected a malfunction of the vehicle emissions control system. Refer to On Board Diagnostics (OBD) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 156).

If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

WARNING

image869

Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic

image870

converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Have your vehicle checked as soon as possible.

image871

The service engine soon indicator light illuminates when you first switch on the ignition before engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing.

Normally, the service engine soon light stays on until you crank the engine, then turns itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 156).

image872

image873 Displays when the AdvanceTrac®/Traction control

image874

E138639 is active. If the light remains on, have the system serviced immediately. See Using Stability Control (page 178).

Stability Control System Off

image875 Illuminates when you disable AdvanceTrac®/Traction. See

image876

image877 Using Stability Control (page 178).

Transmission Tow/Haul (If Equipped)

Illuminates when you activate the tow/haul feature. If the light

image878

E161509 flashes steadily, have the system serviced immediately. Damage to the transmission could occur. See Automatic Transmission (page 159).

4X2

Illuminates momentarily when you engage two-wheel drive

image879

E181778 high. If the light fails to display or remains on when the ignition is on, have the system serviced immediately by an authorized dealer.

4X4 Auto

Illuminates when you engage the four-wheel drive system. If the

image880

E181781 light fails to display or remains on when the ignition is on, have the system serviced immediately by an authorized dealer.

89

image881

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image882image883

Instrument Cluster

image884

4X4 LOW

Illuminates when you engage

image885

four-wheel drive low. If the light E181780 fails to display or remains on when the ignition is on, have the system serviced immediately by an authorized dealer.

4X4 HIGH

Illuminates when you engage

image886

four-wheel drive high. If the light

E181779  fails to display or remains on

when the ignition is turned on, have the

system serviced immediately by an

authorized dealer.

AUDIBLE WARNINGS AND

INDICATORS

Key in Ignition Warning Chime

Sounds when you leave the key in the

ignition and the driver door open.

Headlamps On Warning Chime

Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver door is open.

Parking Brake On Warning Chime

Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by an authorized dealer immediately.

Direction Indicator Chime

Sounds when you leave the direction indicator on after signaling a turn and driving the vehicle more than 1.5 miles (2.4 km).

90

image887image888

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image889image890

Information Displays

image891

GENERAL INFORMATION

WARNING

image892

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that

image893

you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

image894

You can control various systems on your vehicle using the information display controls on the steering wheel. Corresponding information shows in the information display.

Information Display Controls (Type 1 and 2)

image895

E205351

91

image896

Press the up and down arrow buttons to scroll through and highlight the options within a menu.
Press the right arrow button to enter a sub-menu.
Press the left arrow button to exit a menu.
Press the OK button to choose and confirm a setting or message.

The arrows in the upper left corner of the display indicate additional content available when lit.

Main menu (type 1)

From the main menu bar on the left side of the information display, you can choose from the following categories:

Display Mode.
Trip 1 & 2.
Fuel Economy.
Driver Assist.
Settings.

Scroll up/down to highlight one of the categories, then press the right arrow key or OK to enter into that category. Press the left arrow key as needed to exit back to the main menu.

Display Mode

Use the arrow buttons to choose between the following display options.

image897

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image898image899

Information Displays

image900image901

Display Mode

image902 Distance to E

image903 Digital Speedo

image904 Oil Press

image905 Oil Temp

image906 Trans Temp

Trip 1 & 2

Use the arrow buttons to choose between the following.

Note: Pressing OK stops/starts the timer.

Holding OK resets the odometer and timer.

image907

Trip 1 & 2

image908 Trip Odometer

image909 Trip Timer

image910 Average Fuel

Trip Odometer — Registers the distance traveled of individual journeys.
Trip Timer — Registers the time of individual journeys.

Fuel Economy

Use the arrow buttons to choose the desired energy display.

Average Fuel— Indicates the average fuel consumption since the function was last reset.

image911

Fuel Economy

image912 Distance to E

image913 Inst Fuel Econ

image914 Long Term Average Fuel

image915 Average Speed

Driver Assist

In this mode, you can configure different driver setting choices.

Note: Some items are optional and may not appear.

92

image916image917

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image918image919

Information Displays

image920image921

Driver Assist

image922 DTE Calculation image923 Normal history used or Towing history used

image924 Engine Hours image925 Engine Hours XXXXX

image926 Engine Idle Hours image927 Engine Idle Hours XXXXX

Settings

In this mode, you can configure different driver setting choices.

Note: Some items are optional and may not appear.

image928

Settings

Vehicle

Trlr Sway Control – check enabled or uncheck disabled

Trlr Brake Mode

Elect., Surge, None

Elect. over Hydraulic

Lighting

Autolamp Delay

Select time interval

Locks

Autolock – check enabled or uncheck

disabled

Autounlock – check enabled or uncheck

disabled

Remote Unlock

All Doors or Driver

Oil Life Reset

Set to XXX% – Hold OK to Reset

Power Liftgate

Enable or Disable switch

Wipers

Courtesy Wipe

MyKey*

Create MyKey

Hold OK to create MyKey

911 Assist

Always On or User Selectable

Do Not Disturb

Always On or User Selectable

Traction Control

Always On or User Selectable

Max Speed

65 MPH (105 km/h), 70 MPH (110 km/h),

75 MPH (120 km/h), 80 MPH (130 km/h)

or Off

Speed Minder

45 mph (72 km/h), 55 mph (89 km/h), 65

mph (105 km/h) or Off

93

image929image930

Expedition (TB7) Canada/United States of America, enUSA, Edition date: 201604, Second Printing

image931image932

Information Displays

image933image934

Settings

image935 Volume Limiter – check enabled or uncheck disabled

image936 Do Not Disturb image937 Always On or User Selectable

image938 Clear MyKeys image939 Hold OK to Clear All MyKeys

Display Setup image940 Distance image941 Miles & Gallons, L/100km or km/L

image942 Temperature image943 Fahrenheit or Celsius

image944 Language image945 Select Language – Hold OK to set language image946

*Some MyKey items only appear if a MyKey is set.

Main Menu (type 2)

From the main menu bar on the left side of the information display, you can choose from the following categories:

Display Mode.
Trip/Fuel.
Towing.
Off Road.
Settings.

Scroll up/down to highlight one of the categories, then press the right arrow key or